某轻客整车风阻系数有限元分析与优化
2021-06-20张汤赟邹亮袁刘凯
张汤赟 邹亮 袁刘凯



摘 要:本文对某轻型客车进行有限元建模,开展了整车风阻系数仿真分析,并利用整车风洞试验验证了仿真模型和仿真结果的合理性和有效性。基于对原型车的外流场分析,提出了三个降低整车风阻系数的优化措施,分别为增大前挡风玻璃迎风角度、调整尾翼翘角、增大后门倾斜角度,并研究了各措施中关键参数对风阻系数的影响。对各优化措施的仿真分析表明,前挡风玻璃迎风角度增大3°可将整车风阻系数降低4.5%;尾翼下翘有利于整车风阻系数的降低;整车风阻系数随汽车后門倾斜角度的增加而降低,可根据实车需求合理设计后门倾斜角度。
关键词:风阻系数;CFD仿真;风洞试验;流场分布
中图分类号:U467.1 文献标识码:A 文章编号:1005-2550(2021)01-0093-07
Finite Element Modeling and Optimization of
Drag Coefficient for a Light Bus
ZHANG Tang-yun, ZOU Liang,YUAN Liu-kai
( Nanjing Iveco Automobile Co., Ltd., Nanjing 211806, China)
Abstract: The finite element model of a light bus is established and the vehicle drag coefficient is simulated and analyzed. The rationality and effectiveness of the simulation model and simulation results are verified by vehicle wind tunnel test. Based on the analysis of the external flow field of the prototype vehicle, three optimization measures are proposed to reduce the vehicle drag coefficient, which are increasing the windward angle of the front windshield, adjusting the warping angle of the rear wing, and increasing the tilt angle of the rear door. The influence of key parameters in each measure on the drag coefficient is also studied. The simulation results show that the vehicle drag coefficient can be reduced by 4.5% by increasing the windward angle of the front windshield by 3°. The downward warping of the rear wing is beneficial to the reduction of the vehicle drag coefficient. The vehicle drag coefficient decreases with the increase of rear door tilt angle. The rear door tilt angle can be reasonably designed according to the actual vehicle demand.
Key Words: Drag Coefficient; CFD Simulation; Wind Tunnel Test; Flow Field Distribution
张汤赟
毕业于清华大学,工程硕士,现就职于南京依维柯汽车有限公司产品工程部,任整车集成科高级经理,高级工程师。
1 引言
空气动力学特性是汽车的重要特性之一,它直接影响汽车的动力性、燃油经济性、操纵稳定性、舒适性与安全性[1]。汽车风阻系数是判断汽车动力学特性的指标之一,风阻系数每降低 10%,汽车可以节省燃油 7%。因此,降低汽车风阻系数越来越受到各汽车厂家的重视。对车身造型的优化是改善汽车空气动力学特性,降低整车风阻系数的重要手段。汽车空气动力学研究方法主要有理论分析、试验研究和数值模拟[2]。汽车空气动力学的数值模拟方法一般称为计算流体力学(CFD),具有耗时短、操作简便、结果不受实验条件影响等优势,在汽车空气动力学性能的研究中应用最为广泛[3]。……
