压褶效果褶皱机织物设计与织造
2021-11-28何恬颖田伟金肖克贺荣白楚钰祝成炎
何恬颖 田伟 金肖克 贺荣 白楚钰 祝成炎



摘要:
压褶因其良好的立体效果,广泛应用于面料设计中。现有压褶面料大多采用机械压褶获得,这对原料的耐热性有一定要求,限制了原料的种类。文章提出利用特殊打纬方式和纱线间收缩性差异两种直接织造方法实现面料的压褶效果,既可增加原料种类,又能省去中间压烫工序。通过对这两种方法织造所获得的试样进行分析比较,最终选择铺设弹性纱的方式,织造1、2、3 cm三种不同褶皱宽度的压褶效果试样,并对三种试样进行弹性回复测试,结果表明铺设弹性纱方式可成功织造出保形性较好的压褶效果褶皱机织物。
关键词:
压褶;成形工艺;褶皱织物;包覆纱;重经组织;立体效果;纺织品设计
中图分类号: TS105.1
文献标志码: A
文章编号: 10017003(2021)11010805
引用页码: 111301
DOI: 10.3969/j.issn.1001-7003.2021.11.018
Design and weaving of woven pleated fabric with compressive fold effect
HE Tianying1, TIAN Wei1, JIN Xiaoke1, HE Rong2, BAI Chuyu1, ZHU Chengyan1
(1.College of Textile Science and Engineering (International Institute of Silk), Zhejiang Sci-Tech University, Hangzhou 310018, China;2.Hangzhou Sericulture Ancient Silk Network Technology Co., Ltd., Hangzhou 310018, China)
Abstract:
Compressive fold is widely used in fabric design because of its good stereoscopic effect. Most of the existing compressive fold fabrics are weaved by mechanical pleating, setting certain requirements for the heat resistance of fabrics and limiting the types of raw materials. In this paper, two methods to directly weave compressive fold fabrics were proposed: special beating-up method and the method of using different shrinkage between yarns. Both can increase the types of raw materials and eliminate the intermediate pressing process. Through the analysis and comparison of the samples obtained by these two weaving methods, the method of laying elastic yarns was finally selected to weave samples with different fold widths of 1 cm, 2 cm and 3 cm. Through the elastic recovery tests on three samples, the results show that the woven pleated fabric with good shape retention can be successfully woven through the method of laying elastic yarns.
Key words:
compressive fold; forming technology; pleated fabric; wrap yarn; double warp weave; stereoscopic effect; textile design
作者簡介: 何恬颖(1989),女,硕士研究生,研究方向为现代纺织工艺、新产品研究与开发。通信作者:祝成炎,教授,cyzhu@zstu.edu.cn。
褶皱作为一种重要的设计元素,广泛应用于服装造型和纺织品设计中,在众多褶皱种类中,压褶由于其规整灵动的特征在市场中十分受欢迎[1-2]。目前,市场上的压褶面料大多采用机械压褶制得,利用机器的压力、高温压烫的热力等改变面料的表面形态结构[3],因此机械压褶对原料的耐热性有一定的要求,限制了原料的种类,而压褶机的滚筒间距又限制了面料的厚度及面料的季节风格,在多层压褶方向上存在困难[4]。
机织成型法是将原料、组织、织造工序等各种工艺条件进行配合,从而直接织造出具有褶皱效果的面料,省去压烫过程,打破机械压褶面料中原料和面料厚度的局限性、拓宽压褶面料季节适应性并缩短生产路线的织造方式。……
