薄板带陶瓷衬垫埋弧焊工艺研究
2020-04-20曹小兵
曹小兵



摘要:对薄板埋弧焊焊接过程中易出现的焊接缺陷、产生原因进行了探讨,通过薄板带陶瓷衬垫埋弧焊和未加陶瓷衬垫普通埋弧焊对比选取较优的工艺方案,并对宏观形貌、力学性能等进行研究分析。结果表明,薄板带陶瓷衬垫埋弧焊工艺焊接时电弧稳定,单面焊双面成形,焊缝成形饱满、整齐、美观,焊缝与母材圆滑过渡,焊缝无气孔、裂纹、未熔合、夹渣等缺陷,力学性能合格,焊缝质量稳定优良;该工艺适用于薄板、狭小空间、密闭容器槽罐的焊接,并且具有节能环保、质量优良、提高工效、降低成本等优点。
关键词:陶瓷衬垫;薄板;埋弧焊
中图分类号:TG 444
Abstract:In this paper, the common quality problems and causes of welding defects in the process of thin plate submerged arc welding are analyzed, submerged arc welding with ceramic backing and common submerged arc welding without ceramic backing process are compared, macroscopic feature and mechanical property are tested. The results show that the welding arc is stable, single side welding is doublesided forming, the weld is full, neat and beautiful, the weld and base metal are smooth transition, the weld is free of defects such as porosity, crack, lack of fusion, slag inclusion, etc. The mechanical property test is qualified, and the weld quality is stable and excellent. It is suitable for thin plate welding, narrow space and closed container tank due to its advantages in energy saving and environmental protection, excellent quality, high efficiency and low cost.
Key words:ceramic backing;thin plate;submerged arc welding
0 前言
埋弧焊作为当今焊接生产中最普遍使用的焊接方法之一,由于其具有机械化程度高、生产效率高、焊接质量稳定、成本低等优点,被广泛应用于压力容器制造行业中[1]。
中铝万成山东建设有限公司近期承接了批量压力容器制造和非标槽罐设备的制作,大部分是板厚8 mm以下、直径2 m以下的薄板容器槽罐制作,此批设备量大,工期要求紧,制作工期长,劳动强度大,所需焊工人员数量多,若完全采用焊条电弧焊明显无法满足要求。
大批量、小直径的薄板容器槽罐制作,一般采用常规的焊接方法和工艺,先用焊条电弧焊打底焊接,再用埋弧焊焊接,焊后背部碳弧气刨清根打磨,再用埋弧焊或焊條电弧焊焊接。通过多次试焊发现,薄板埋弧焊时易产生气孔、夹渣等缺陷,特别是封头与筒节连接的环焊缝气孔明显超标,造成焊缝返修,而且无法实现单面焊双面成形,需要人工碳弧气刨清根劳动强度大、焊接效率低,无法满足工期要求。……
