APP下载

高速PCB板谐振仿真与分析

2014-07-19孟晶俞能杰

现代电子技术 2014年10期

孟晶 俞能杰

摘 要: 谐振是电源完整性一大问题,PCB电源平面间谐振振幅过大,会导致电源分配系统(PDS)工作异常,甚至成为EMI辐射源,故在PCB详细设计阶段需开展谐振仿真分析并消除谐振,从而提高设计成功率。为消除谐振,首先利用SIWAVE软件对电源地平面间谐振情况进行仿真分析,找出谐振点,然后合理选用布局去耦电容,消除400 MHz以下频段谐振影响。通过调整PCB叠层及层间距消除400 MHz以上频段谐振影响。通过实例仿真分析,依据工程经验,实现了快速估算去耦电容的计算方法,并证明了其正确性。

关键词: 电源完整性; 谐振; SIWAVE仿真分析; 去耦电容

中图分类号: TN710?34 文献标识码: A 文章编号: 1004?373X(2014)10?0144?03

Abstract: Resonance is a major problem of power integrity. If the resonance amplitude between PCB power planes is too large, it may cause PDS work abnormal, even cause the power planes to become EMI emitter, so in the detailed PCB design stage, simulation analysis of resonance and eliminating resonance are needed for improving the success rate of the design. To eliminate resonance, first, the SIWAVE is used to simulate and analyze the resonance between the power planes to find the resonance point, and then the decoupling capacitor is selected and layouted reasonably, so as to eliminate the influence caused by the resonance below 400 MHz frequency, and eliminate the influence caused by the resonance above 400 MHz frequency by adjusting the PCB overlayers and the space between overlayers. Based on engineering experience, a rapid calculation method to estimate the value of the decoupling capacitors was achieved. Its correctness was proved with simulation analysis on example.

Keywords: power integrity; resonance; SIWAVE simulating and analysis; decoupling capacitor

0 引 言

随着微电子技术的不断发展,更多功能的模拟和数字电路被制作或集成到单个芯片中[1]。当大量高速开关器件同时快速切换状态时,就会产生电源噪声,干扰周围的高速信号,并且由于噪声容限变小,严重时,可引发芯片的误动作,造成不利影响。因此对电源完整性的研究显得越来越重要[2?3]。

作为电源完整性的一大问题,谐振是指能量被夹在两个平行板(power and ground plane)之间,因原始信号与其反射信号同相(phase add)而形成共振腔效应。在中低频时,电源地平面对可当作一个理想电容来看待,其ESR和ESL都很小,在频率达到某一个高频段时,电源地平面间变成了一个谐振腔,等效为RLC串并联电路,在谐振频率点附近,平面对地阻抗变得很大,从而引发电源完整性问题[4]。

1 谐振带来的问题

若谐振落在了设计关注的频段内,带来的问题,需要从三方面来分析:一方面谐振过大,在谐振点处电源波动过大,稳压电源芯片VRM无法实时响应负载对于电流需求的快速变化,会出现电源跌落,从而产生电源噪声[5];……

登录APP查看全文