搭接焊铝塑管与对接焊铝塑管的长期静液压强度计算
2011-11-04李明轩
李明轩
搭接焊铝塑管与对接焊铝塑管的长期静液压强度计算
李明轩
(四川大学高分子科学与工程学院,四川成都610065)
将16~32规格的搭接焊铝塑管的长期静液压试验曲线外推至50年,通过考虑与对接焊铝塑管相同的总体设计系数(C=1.25),证明在T0=95℃的长期工作温度下,16~32规格的搭接焊铝塑管与对接焊铝塑管的允许工作压力(P0)相当。搭接焊铝塑管也能满足95℃、1.25 MPa下使用寿命为50年的要求。根据国家标准对搭接焊铝塑管与对接焊铝塑管的铝管层最小壁厚和最小拉伸强度的要求,计算出16~50规格的搭接焊铝塑管与对接焊铝塑管的P0。结果表明,小规格二者的P0相当,大规格对接焊铝塑管的P0优势明显。
铝塑管;对接焊;搭接焊;长期静液压强度
Abstract:The long-term hydrostatic pressure test curves of overlap-welding aluminum-plastic pipes with diameters of 16 mm to 32 mm were extrapolated to 50 years by considering the same overall design factor as 1.25 with butt-welding aluminum-plastic pipes.It showed that at 95℃long-term operating temperature,overlap-welding aluminum-plastic pipes with diameters of 16 mm to 32 mm had a comparative allowable working pressure(P0)compared with butt-welding aluminum-plastic pipes,and could meet the requirements of the 50-year service life under 95℃and 1.25 MPa.According to the requirements of minimum thickness and minimum tensile strength of aluminum layer in national standards,P0of the overlap-welding aluminum-plastic pipes and butt-welding aluminum-plastic pipes with diameters of 16 mm to 50 mm was calculated.The results showed that both had the sameP0for the small size,but butt-welding aluminum-plastic pipes had the obvious advantage for the large size.
Key words:aluminum-plastic pipe;butt-welding;overlap-welding;long-term hydrostatic pressure strength
0 前言
铝塑管因其轻质、高强、耐温、耐压、弯曲不反弹、安装方便且100%隔绝气体渗透等优点,广泛应用于建筑冷热水、室内燃气和高温散热器采暖等领域。根据铝管焊接方式不同可分为搭接焊铝塑管与对接焊铝塑管。搭接焊是通过超声波能量使搭接铝带界面处熔化而焊接成管,因为是搭接,焊接面较宽,所需铝带较薄。对接焊是通过氩弧或激光的高温使对接处铝带完全熔化成管。因为要保证对接时的焊接面积,所需铝带较厚。由于对接焊铝管更厚,通常认为对接焊铝塑管比搭接焊铝塑管适用于更高温度和压力的场合,GB/T 18997.2—2003《铝塑复合压力管第2部分:铝管对接焊式铝塑管》中规定XPAP1和XPAP2在95℃长期工作温度 (T0)下,P0=1.25 MPa[1]。而 GB/T18997.1—2003《铝塑复合压力管第1部分……
