基于CFD-DEM的循环阀清洁器携屑特性研究
2025-08-07胡伟关宁张燕萍徐丙贵张金亚朱宏武
中图分类号:FE242文献标识码:A DOI:10.12473/CPM.202407035
Research on Cuttings Transport Performance of Circulating ValveCleanerBasedonCFD-DEM
Hu Wei1Guan Ning² Zhang Yanping²Xu Binggui²Zhang JinyalZhu Hongwu1 (1.ColegeofMechncalndansportationngineeing,CinaUniesitofPetrole(Beijing);.CNCEnineeingechol ogyRamp; D Company Limited)
Abstract: In the processof drilling,inefficient drill cuttings transport may lead toan increase inannular cuttings concentration and equivalent circulating density(ECD),thereby causing some problems such as tool wear and lost circulation.To solve these problems,anew type of borehole annulus circulating valve cleaner was developed.Basedonthe H-B non-Newtonian fluid model,a numerical model for evaluating the cutings transport performance of multi-stage borehole annulus circulating valve cleaner was built by using the coupled CFD-DEM calculation method.The effctsof the number of nozzles,nozzle diameter,nozzleangle and drillpipe rotation speed on thecuttings transport performance of the circulating valve cleaner were analyzed.The results show that increasing thediameterandnumber ofnozles orraising the drillpipe rotation speed leads to an increase in theconcentration of cuttings in annulusanda significant decrease in the cutings transport ratio(CTR).When the numberof nozzles is 3 and the nozzle diameter is 10mm ,the cuttings transport performance is the best. As the nozzle angle increases,the CTR value increases and then decreases. When the nozzle angle is 30∘ , the CTR value is the highest,indicating the highest cutings transport efficiency.Invertical borehole,the rotationofthe circulating valve cleaner produces aswirling effect,whichmaycausethe spiral migrationof cutings,therebymaking cuttings retain longerinthe borehole to induceasignificantreductioninthecuttings transportefficiency.Thehighertherotational speed,the stronger the swirling effect,and the worse thecutings transport performane.Given the above optimal parameters,the borehole annulus flow rate increases by nearly 58% and the overall CTR increases by nearly 10% (20 after using the proposed circulating valve cleaner.The research conclusions are of great significance for improving the efficiency of annulus cuttings transport and ensuring efficient and safe oil and gas development.
Keywords: multi-stage borehole;circulating valve cleaner;cutings transport efficiency; CFD-DEM nozzle;drill pipe rotation speed
0 引言
在油气钻井过程中,钻头破碎岩石产生的大量岩屑需要被及时清理出井筒。自前,低效率的岩屑去除仍然是钻井作业面临的最大挑战之一。岩屑在井筒中的沉积会导致机械钻速降低,延长了非生产时间(NPT),并可能导致堵塞,造成扭矩和阻力过大[1-4]。此外,低效的岩屑输运还会导致环空岩屑体积分数增大,压降升高。这会进一步导致钻井液的等效循环密度(ECD)增大,并引发一系列的井壁稳定性问题[5-7]。因此,深入开展井筒内岩屑的运移机制研究,提高岩屑清洁效率,对高效、安全的油气开发至关重要。
近年来,国内外相关机构和学者在环空岩屑输运方面开展了大量研究工作[8-12]。宋先知等[13-15]采用CFD和试验方法,分析了多种参数对偏心环空岩屑运移的影响规律,并开发了新的旋流式井筒清洁工具。S.AKHSHIK等[利用CFD-DEM方法研究了倾斜细孔中岩屑的临界沉积速度与环空底部的岩屑沉积规律。HUW.等[17]结合CFD-DEM和试验方法,全面分析了岩屑在非牛顿流中的运移规律,并提出了评价井眼清洁效率的通用方法。还有学者利用CFD-DEM方法研究了四叶形钻杆[18]和岩屑移除工具[19]对井眼清洁过程中岩屑输运效率的影响。然而,这些研究几乎针对的是单一直径的环空段,而在多级井眼中,井身结构通常由多段不同直径的井眼组成。流体从小井眼进入大井眼后速度会迅速减小,导致岩屑输运效率降低。而循环阀清洁技术在有效增加环空流速的同时可以辅助携屑,从而提升岩屑的输运效率。……
