粉质粘土路基冲击压实动力响应数值模拟研究
2016-04-20宋修广陈晓光于一凡
宋修广 陈晓光 于一凡



摘要:依托实际工程,应用有限差分软件FLAC3D分层建立高速公路粉质粘土路段路基模型;通过在路基模型顶面施加1次动力荷载和施加不同次数动力荷载,对路基模型的动力响应进行数值模拟分析,研究了冲击作用下动应力、竖向位移沿深度和径向距离的变化规律。结果表明:冲击轮冲击路基表面破坏土体结构,从而使路基土体密实,冲击碾压加固路基效果显著;土体中加固区近似为椭球体,其剖面为椭圆形;土体中动应力、竖向位移沿径向的衰减速度大于竖向的衰减速度,径向的影响宽度小于竖向影响深度;当冲击压路机保持正常的工作速度12 km·h-1,路基填筑高度为1 m时,冲击碾压次数宜在20次左右。
关键词:基础工程;动应力;数值模拟;路基;冲击碾压;竖向位移
中图分类号:TU435文献标志码:A
Abstract: Relying on the actual project, asubgrademodel of silty clay in highway was built by using the numerical calculation software FLAC3D. Numerical simulation analysis about dynamic response of subgrade model was carried through applying one time dynamic load and different times dynamic load on the top of the subgrade model, and the change laws of dynamic stress and vertical displacement along depth direction and radial direction were researched. The results show that the soil structure is damaged by impact roller impacting subgrade surface, so that the subgrade soil is compacted, impact compaction has obvious reinforcement effect on subgrade. The reinforcement area in soil is like ellipsoid, and its profile is like ellipse. The attenuation velocities of dynamic stress and vertical displacement along radial direction are faster than those along vertical direction, and the radial influence width was greater than the vertical influence depth. When impact roller keeps the normal working speed 12 km·h-1 and subgrade filling height is 1 m, the time of impact roller compaction shouldbe about 20.
Key words: foundation engineering; dynamic stress; numerical simulation; subgrade; impact roller compaction; vertical displacement
0引言
冲击碾压法是利用冲击压路机对路基或地基进行冲击碾压,以提高土的强度和压实度,防止土不均匀沉降的一种低能量浅层加固方法[1]。大量现场试验表明,经过冲击碾压后的路基不仅沉降周期大幅度缩短,工后沉降也大幅减小[23]。19世纪80年代冲击压实设备最早被提出,20世纪50年代南非Aubrey Berrange公司提出非圆形碾,但是直到20世纪70~80年代南非国家运输和道路研究所(NITRR)经过多年研究,才使冲击碾压成为一种可靠的技术,并制造出可供实用的非圆滚轮压路机[4]。1995年冲击碾压法首次在中国应用,用于处理香港赤腊角新机场的场道[5],其后冲击碾压法被广泛应用于机场建设的地基处理中,如新疆且末机场工程、广州白云国际机场迁建工程、重庆万州机场工程和上海浦东国际机场二期工程[69]。……
