APP下载

Effect of Pb content on the surface topography and corrosion resistance of hot dip Zn-Al-Mg coatings

2016-02-17CHENGGuopingJINXinyanandXIEYingxiu

Baosteel Technical Research 2016年4期

CHENG Guoping,JIN Xinyan and XIE Yingxiu

1)Research Institute,Baoshan Iron & Steel Co.,Ltd.,Shanghai 201900,China;2)State Key Laboratory of Development and Application Technology of Automotive Steels(Baosteel),Shanghai 201900,China

Effect of Pb content on the surface topography and corrosion resistance of hot dip Zn-Al-Mg coatings

CHENG Guoping1),JIN Xinyan1,2)and XIE Yingxiu1)

1)Research Institute,Baoshan Iron & Steel Co.,Ltd.,Shanghai 201900,China;2)State Key Laboratory of Development and Application Technology of Automotive Steels(Baosteel),Shanghai 201900,China

In this study,the effect of Pb content on the surface morphology and salt spray corrosion resistance of hot dip Zn-Al-Mg coatings was investigated.The results showed that the coating surface easily formed small grains of zinc spangle structures and that the salt spray corrosion resistance of the coating decreased when Pb content was greater than 0.01%.The microstructure and energy dispersive spectrum analysis of surface and cross-sectional areas was performed by scanning electron microscopy.Pb content present in the coating was analyzed by glow discharge spectrum.The results showed that the distribution of Pb in the coating was not uniform.The Pb content was segregated on the surface and at the cross-section of the Zn-Al-MgZn2ternary eutectic structure,especially,on the surface of the Zn-Al-MgZn2ternary eutectic structure.

Pb content; hot dip Zn-Al-Mg coatings; surface topography; corrosion resistance

1 Introduction

In the last 20 years,one of the important topics in the field of hot dip galvanizing was the development of the Zn-Al-Mg coating.The earliest research work was initiated by Inland Steel of the United States in 1969 and the patent of the product and manufacturing method was applied[1-2].Nisshin Steel of Japan has successfully produced Zn-Al-Mg coated steel sheets commercially since 1997[3],with the annual production capacity exceeding 1.2 million tons(Mt).Nippon Steel of Japan also developed a family of Zn-Al-Mg coatings(Superzinc coating in 1980,Dymazinc coating in 1997,and Superdyma coating in 2001[4-6]),with the annual production capacity exceeding 0.56 Mt.These Zn-Al-Mg coating products were mainly used for construction purposes that require high corrosion resistance.Since 2006,European steel companies launched a new family of low-aluminum Zn-Al-Mg coatings[7-11],in which the composition of aluminum ranged from 1% to 3.7% and the magnesium composition ranged from 1% to 3%.Much effort have been put in to expand the application of these new Zn-Al-Mg coatings in the automotive industry.In 2013,BlueScope Company of Australia announced a new generation of galvalume.The new coating was based on the original galvalume but 2% Mg was added,significantly improving the corrosion resistance of the product.The coating was mainly used in construction requiring thin sheets(thickness <1.2 mm,typical thickness=0.42 mm)[12].Recently,Nippon Steel & Sumitomo Metal Cor-poration and BlueScope Steel conducted a cooperative research for a new generation of ZINCALUME and published relevant papers[13-14].From the above papers,the enhanced corrosion resistance of the products was reported,and the main elements of Si,Mg,and Al were highlighted.In traditional hot dip galvanized(GI)products,the content of Pb has a significant effect on the surface and other properties of the coatings[15-17].In this study,the effect of Pb content on the surface morphology and salt spray corrosion resistance of Zn-Al-Mg coating was investigated.

2 Experimental materials and processes

The substrate for hot dip galvanizing in Iwatani IV hot dip simulator is a commercially produced CQ grade cold rolled plate with a thickness of 0.7 mm.The process of hot dip galvanizing includes recry-stallization annealing,cooling,hot dip coating,and cooling after coating.Bath composition is shown in Table 1.

Table 1 Chemical composition of bath %

Initially,the surface of the sample was subjected to visual observation.Next,the surface morphology and cross-section morphology of the coating were observed by optical microscope and by a scanning electron microscope.Glow discharge spectrum(GDS)was used to detect the distribution of elements along the coating thickness.

Salt spray tests(SST)were performed according to the ASTM B117 standard,and the time to reach 5% red rust was recorded.Kvalues were used to char-acterize the difference of salt spray corrosion resi-stance between the sample coating and GI coating.

We definedKas follows:

K=(time to reach 5% red rust in SST of sample coating / coating thickness) / (time to reach 5% red rust in SST of laboratory GI / GI coating thickness)

The coating thickness was measured by a MP 2.0 Dualscope manufactured by Fischer Technology Inc.

3 Results and discussion

3.1 Surface morphology

After hot dip galvanizing in the laboratory,the surface zinc spangle was not visible by the naked eye for 1#,2#,and 5#samples.However,there was scattered zinc spangle on the surface of 3#sample,and zinc spangle was obviously evident on the surface of 4#sample.The visual,optical,and scanning electron microscopy(SEM)images of the surface of the typical sample were shown in Fig.1.The enlarged structure of zinc spangle presented a feather structure,which was the result of a specific arrangement of the primary zinc phase,as shown in Fig.2.It was shown that the addition of Pb content affects the formation of the primary zinc phase,resulting in the display of a regular arrangement of the primary zinc phase in local area during the solidification of the coating,finally showed the appearance of zinc spangle.

3.2 Comparison of salt spray corrosion resis-tance of coatings

The salt spray corrosion performance of the sample coatings was shown in Fig.3,which demonstrated that salt spray corrosion resistance of the coatings was obviously enhanced with the increase of Al and Mg contents in the coating.However,the salt spray corrosion resistance of the coating was significantly decreased by the addition of 0.011% Pb content.In other words,the high content of Pb in the coating was detrimental to the salt spray corrosion resistance;thus,we must control Pb content to the lowest possible level.

3.3 Distribution of Pb in the coating

Fig.4 detailed a surface morphology and energy dispersive spectrum(EDS)analysis of 4#sample coating under SEM.The surface has a large number of primary zinc phases,a Zn-MgZn2binary eutectic structure,and a Zn-Al-MgZn2ternary eutectic structure.EDS analysis showed that Pb was distributed in the Zn-Al-MgZn2ternary eutectic structure.Fig.5 showed a cross-sectional morphology and EDS analysis of 4#sample coating under SEM.The main part of the coating was the primary zinc phase,and Pb was distributed in the Zn-Al-MgZn2ternary eutectic structure.

Fig.3 Comparison of salt spray corrosion resistance of sample coatings

The graph in Fig.6 displays the result of GDS analysis along the coating thickness.The results show that the distribution of Pb in the coating is not uniform and is segregated in the surface of the coating.This may be due to the low melting point of Pb(327 ℃)[18];therefore,Pb particles form in the final stage of solidification of the coating.

A common view is that Pb particles will lead to intergranular corrosion in the grain boundaries of the coating and will shorten the life of the coating significantly.The corrosion mechanism of Pb,which leads to decreased corrosion resistance of Zn-Al-Mg coatings,needs to be further investigated in the future.

4 Conclusions

(1) The effect of Pb content on the hot dip galvanized Zn-Al-Mg coating easily generated small zinc spangle grain structures on the coating surface,which was the result of regular arrangement of the primary zinc phase in the process of coating solidification.

(2) A high Pb content in the coating signifi-cantly reduced the salt spray corrosion resistance of the coating;therefore,Pb content needs to be minimized in the coating.

(3) The distribution of Pb in the coating was not uniform.The Pb content was segregated on the surface and at the cross-section of the Zn-Al-MgZn2ternary eutectic structure,especially,on the surface of Zn-Al-MgZn2ternary eutectic structure.

[1] SIEVERT W C,GEIGER L J and LEE H H.Method of hot dip coating with a zinc base alloy containing magnesium and the resulting product:US3505042[P].1970-04-07.

[2] LEE H H and HALLEY J W.Al-Mg-Zn alloy coated ferrous metal sheet:US3505043[P].1970-04-07.

[3] TSUJIMURA T,KOMATSU A and ANDOH A.Influence of Mg content in coating layer and coating structure on corrosion resistance of hot dip ZnAlMg alloy coated steel sheet[C]∥Galvatech 2001:5thInternational Conference on Zinc and Zinc Alloy Coated Steel Sheet,Brussels,Belgium:145-152.

[4] TANO K and HIGUCHI S.Development and properties of Zn-Al coated steel sheet having excellent corrosion resistance(Super Zinc)[J].Seitetsu Kenkyuu,1984(315):34-41.

[5] SHINDO H,NISHIMURA K,OKADA T,etal.Development and properties of Zn-Mg galvanized steel sheet “DYMAZINC” having excellent corroion resistance[J].Nippon Steel Technical Report,1998(369):61-65.

[6] TANAKA S,HONDA K,TAKAHASHI A,etal.The performance of Zn-Al-Mg-Si hot dip galvanized steel sheet[C]∥Galvatech 2001:5thInternational Conference on Zinc and Zinc Alloy Coated Steel Sheet,Brussels,Belgium:153-160.

[7] BLEEKER R,HANNOUR F,GOOS C,etal.Corus’ new hot dip ZnAlMg coated steel sheet for automobile applications[C]∥Galvatech 2007:7thInternational Conference on Zinc and Zinc Alloy Coated Steel Sheet,Osaka,Japan:510-515.

[8] RAAB A E,BERGER E,FREUDENTHALER J,etal.ZnAlMg hot dip galvanized steel sheets-tribology and tool wear[C/CD]∥Galvatech 2011:8thInternational Conference on Zinc and Zinc Alloy Coated Steel Sheet,Genova,Italy.

[9] SCHULZ J,BENDICK O,WERNER B,etal.ZnMg coatings-Innovation for coil coated steel sheets[C/CD]∥Galvatech 2011:8thInternational Conference on Zinc and Zinc Alloy Coated Steel Sheet,Genova,Italy.

[10] ANGELI G,BRISBERGER R,BULTER M,etal.Zinc magnesium aluminium for automotive industry[C]∥Galvatech 2013:9thInternational Conference on Zinc and Zinc Alloy Coated Steel Sheet,Beijing,China:632-636.

[11] SOHN H,LEE J,YOO Y,etal.Corrosion behaviors of Zn-MgZn2eutectic structure in ZnAlMg coatings[C/CD]∥Galvatech 2011:8thInternational Conference on Zinc and Zinc Alloy Coated Steel Sheet,Genova,Italy.

[12] LIU Q Y,WILLIAMS J,NOLAN D,etal.Development of Mg-containing 55%Al-Zn coated steel for building applications[C]∥Galvatech 2015:10thInternational Conference on Zinc and Zinc Alloy Coated Steel Sheet,Toronto,Canada:208-215.

[13] FUJII S and SHIMODA N.Development of Mg-added 55%Al-1.6%Si-Zn coated steel sheets[C]∥Galvatech 2015:10thInternational Conference on Zinc and Zinc Alloy Coated Steel Sheet,Toronto,Canada:807-812.

[14] SHEDDEN B,WATERS A,FORD S,etal.New procedure for mass loss corrosion testing of magnesium-containing coated steel products[C]∥Galvatech 2015:10thInternational Conference on Zinc and Zinc Alloy Coated Steel Sheet,Toronto,Canada:789-796.

[15] LI G L.Effects of impurities on corrosion resistance of the coat of galvanizing by dipping[J].Steel Wire Products,1999,25(4):10-13.

[16] ZHENG H D.Influence of Pb in zinc bath on hot dip galvanized sheet[J].Research on Iron and Steel,1993,71(2):15-19.

[17] CHANG L L,CHEN H X,SUN J,etal.Effect of spangles on corrosion resistance of passivated hot galvanizing plate[J].Materials Protection,2005(11):49-50.

[18] XU B S.Lead and its use[J].Metal World,1996(6):12-13.

CHENG Guoping; E-mail: chengp@baosteel.com

10.3969/j.issn.1674-3458.2016.04.004


登录APP查看全文