冲击荷载下基于动力宏应变的组合梁损伤识别方法研究
2025-08-09李运生贺鼎贾晓远崔春雷荣学亮张彦玲

中图分类号:U448.21 文献标识码:A DOI:10.7535/hbkd.2025yx04011
Research on damage identification method of composite beams based on dynamic macro-strain under impact load
LI Yunsheng 1,2 ,HEDing 1,2 ,JIA Xiaoyuan1,CUI Chunlei³,Rong Xueliang 1,2 ,ZHANG Yanling 1,2
(1.School of Civil Engineering,Shijiazhuang Tiedao University,Shijiazhuang,Hebei O5o043,China; 2.Key Laboratory of the Ministry of Education for Road and Railway Engineering Safety Assurance, Shijiazhuang Tiedao University,Shijiazhuang,Hebei O5oO43,China; 1RoadandBridgeTechnology CompanyLimitedofChina Communications Construction,Shijiazhuang,Hebei O50ooo,China)
Abstract:Inorder toachievedamage identificationof steel-concretecompositebeamsbasedondistributed long-gauge fiber bragggrating(FBG)sensors,modeltestsandfiniteelementanalysisofcomposite beams underimpactloads wereconducted.
The damage assessment index βn constructed from the dynamic macro-strain spectral amplitude was used to identify damage of stelgirder section and stud connections,respectively.Theresearch results show that when long-gauge FBG sensorsare continuouslyarangedalong thelongitudinaldirectiononthebotomsurfaceof steel girder,themacro-strainofthesensors in the damaged area increases significantly. When the evaluation index βngt;0 ,it can be determined that cross-sectional damage has occurred withintherangeofthesensor,andthisindexis more sensitivetothecrack heightonthe webofthe steel girder thantheexpansion width onthe bottom flange.Forstud damage,long-gaugesensorscanbe arrangedin pairs symmetricall on boththeupperandlowersurfacesof theinterface inconcreteslabandstelgirder,andthe measured macro-straintimehistory can be subtracted to obtain the slip macro-strain time history. Then,based on the evaluation index βn obtained from the amplitudeoftheslipmacro-strainspectrum,andusingthetwo-stagidentificationmethod,thelocationofdamagedstudcanbe identfiedeffectively.Overall,easonablearangementoftedistributedlonggaugesensorscanrealizedamageidentificationof differentcomponents instel-concretecompositebeams,especiallytheconnectors whichareconcealed in theconcrete slab.
Keywords:composite structure;stel-concrete composite beam;damage identification;dynamic macro-strain;fiber bragg grating sensors;impact load
由于车辆超载、环境恶化和疲劳反复加载等原因,钢-混凝土组合梁在服役过程中会出现混凝土板开裂、钢梁构件锈蚀断裂及剪力连接件失效等损伤,不仅影响桥梁的外观和正常使用,严重时还会影响结构的承载力和使用寿命,应进行及时准确的损伤识别及性能维护。
应变是反映结构局部刚度变化最直接的数据,但传统的“点式\"应变片很难实现结构表面的全覆盖,而标距长度为 20~1000mm 的分布式长标距光纤布拉格光栅(fiber bragggrating,FBG)应变传感器可以在待测结构表面连续安装,在一维长度方向实现对结构每个位置的健康检测。
长标距传感器测量到的应变是其标距范围内的平均应变,一般称之为宏应变。FBG传感器既可以测试静态宏应变,也可以测试动态宏应变。文献[1-3」分别将FBG传感器应用于预应力混凝土及钢筋混凝土梁的损伤识别和挠度测试;文献[4-5]分别根据有机玻璃模型试验,利用FBG传感器对简支梁和连续梁进行了损伤识别方法的研究;文献[6-7]采用分布式长标距传感器在钢悬臂梁模型试验中实现了一种模态宏应变矢量(MMSV)方法;文献[8]分别构建了基于分布应变能差和相对分布应变能的评估指标,对一座三跨斜拉桥的预应力混凝土主梁损伤进行了识别;文献[9]引人频域分解技术发展了基于MMSV的多点激励下的损伤识别方法;文献[10]采用长标距传感器测试了钢球坠落激励下组合梁的动态宏应变,通过深度学习模型识别了组合梁损伤。……
