APP下载

A newly developed soft-type turtle releasing device (Soft-TRD) for setnet fisheries

2021-07-25DisukeShiodeMikShiozwFuxingHuTdshiTokiYoshioHiri

Aquaculture and Fisheries 2021年4期

Disuke Shiode, Mik Shiozw, Fuxing Hu, Tdshi Toki, Yoshio Hiri

aTokyo University of Marine Science and Technology, Minato, Tokyo, 108-8477, Japan

bNITTO SEIMO Co., LTD., Minato, Tokyo, 105-0004, Japan

Keywords:

ABSTRACT This study investigated a newly developed soft-type turtle releasing device (Soft-TRD) for setnets. Some setnet fish chambers (bag nets) are open at the sea surface, while others are closed (with ceiling netting) and submerged. Sea turtles that stray into submerged bag nets often drown because the ceiling netting prevents them from swimming up to the surface to breathe. The Soft-TRD has a slit that functions as an escape outlet at the center of a 2 m ×2 m netting. The escape slit remains closed, due to the buoyancy of a float attached at each end of the slit, and prevents fish from getting out. Turtles can push the escape slit upward, which opens and allows the turtles to escape. To decide the optimum design of the Soft-TRD, a turtle releasing trial was conducted in an outdoor water tank. Four loggerhead turtles (Caretta caretta) (standard carapace length (SCL): 67.1–72.8 cm) and five green turtles (Chelonia mydas) (SCL: 42.4–63.4 cm) were used for the trial. A single turtle was placed into the experimental bag net where the Soft-TRD (six models in total) was mounted at the center part of the ceiling, and its behavior was observed. All turtles successfully escaped the model with a 150 cm length escape slit, 10 cm overlaying width, and a 4 kgf buoyancy float at each end. The escape slit immediately closed after the turtles escaped. A sea trial (same model) was also performed using a submerged bag net (30 ×10 ×10 m) for two months. Approximately 90% (seven of the eight) of the entrapped loggerhead turtles successfully escaped out through the Soft-TRD. Fishing was not interrupted by the introduction of this device. The use of the Soft-TRD would be helpful in releasing sea turtles from the setnets and contribute to sea turtle conservation efforts.

1.Introduction

Bycatch of endangered species (e.g., some sea birds, sharks, sea turtles, and marine mammals) is an important issue for marine fisheries to manage (Hall et al., 2000; Soykan et al., 2008). A moratorium on high seas drift gillnet fisheries was implemented due to the bycatch of seabirds, marine mammals, and sea turtles (Burke et al., 1994). In 2016,drift nets in Russia’s exclusive economic zone were similarly banned(Lowry, Burkanov, Altukhov, Weller, & Reeves, 2018). From the viewpoint of biodiversity and natural environment conservation, appropriate countermeasures are strongly required to minimize bycatch by marine fisheries.

Sea turtles are endangered species, and all species (except flatback turtles (Natator depressus) for which there is insufficient data), are listed on the IUCN Red List (Godfrey & Godley, 2008; Seminoff & Shanker,2008; IUCN, 2019). In addition to changes of spawning ground conditions and the marine environment, bycatch in marine fisheries has been identified as a cause of decline for the sea turtle population (FAO, 2010;Lewison et al., 2004; Lewison et al., 2013; Wallace et al., 2011). Sea turtles are caught as bycatch by some commercial fisheries from offshore to coastal areas (e.g., pelagic longlines, bottom/drift gillnets, and bottom trawl nets). This has resulted in the development and implementation of techniques to reduce sea turtle bycatch (FAO, 2010, pp.1–128).

Setnets are a passive fishing gear operated along the Japanese coast and provide approximately 40% of the total yield in this area. The setnets commonly used in Japan consist of a lead net, pound nets, funnel nets, and fish chambers (bag nets) (Fig. 1) (Akiyama & Arimoto, 2000;Fujimori et al., 2018; Shiozawa, Shiode, Hu, Tokai, & Hirai, 2018).Migrating fish schools are intercepted by the lead net and then are led into the bag net through the pound net and funnel net. The bag net is usually hauled up by fishermen once a day in the early morning to retrieve the captured species. Major spawning grounds for loggerhead(Caretta caretta) and green (Chelonia mydas) turtles exist along the

https://doi.org/10.1016/j.aaf.2020.06.011 Japanese coast, and the setnets occasionally catch sea turtles in some coastal regions (Ishihara et al., 2011; Shiode et al., 2006). Some bag nets are open at the sea surface, but others are closed with a ceiling netting and submerged, based on the swimming depth of the target species. Sea turtles entering the open bag nets are alive and released by fishermen.Usually, sea turtles breathe at intervals of some minutes during swimming activities (Hays et al., 2000; Houghton, Broderick, Godley, Metcalfe, & Hays, 2002). Hence, turtles straying into the submerged bag net often drown because the ceiling netting prevents them from swimming up to the sea surface to breathe (Gilman et al., 2009; Ishihara et al.,2014; Shiode et al., 2006; Shiozawa, Shiode, Okuyama, Hu, & Tokai,2019). Although the exact amount of bycatch is still unknown, bycatch happening around spawning grounds is feared to have critical effects on sea turtle populations, because of no effective mitigation measures.

The Turtle Excluder Device (TED) is widely used as a method to release sea turtles from trawl nets (Watson & McVea, 1977; Shiode &Tokai, 2004). The TED utilizes the motion of the trawl gear, and the difference in size between turtles and shrimp. Turtles entering the net are forcibly guided to the escape opening via the inclined stainless-steel grid and can exit to the outside. The TED has been modified according to the fishery regulation of the relevant regions and operation styles of the fisheries, for instance, the AusTED has a flexible structure without the metal grid based on the operating environment of its own fishery(Brewer et al., 1998; McGilvray et al., 1999; Mounsey et al., 1995).However, because the setnets are fixed passive fishing gear, techniques such as TED cannot be used in this situation.

A turtle releasing system was developed to reduce incidental deaths of sea turtles in the submerged bag net of the setnet (Shiode et al., 2011).This system consists of a turtle releasing device (TRD) (Shiozawa et al.,2019b; Tamura et al., 2014) and a sloped ceiling netting (quadrangular pyramid shaped) of the bag net. Turtles entering the submerged bag net start to push their heads up repeatedly against the ceiling netting(referred to as push-ups, Shiode et al., 2011) in an attempt to ascent to the sea surface for breaths. The sloping ceiling netting guides the turtles to the highest point of the ceiling netting, leading them to the TRD installed at the top of the pyramid.

The original TRD consisted of a 4 m2base net, with a 1 m2escape vent and a flap door made of a stainless-steel frame covered with a minnow net to prevent fish escape (Shiozawa et al., 2019a; Tamura et al., 2014). However, problems may arise during fishing operations,especially when hauling up the bag net, because the flap door was made of a solid frame. Therefore, the design of the TRD must be revised to eliminate any fishing obstacles, without losing the functions required for the TRD.

Fig. 1.Diagram of the setnet used in the operational test in this study. The setnets commonly used in Japan consist of a lead net, pound nets, funnel nets, and fish chambers (bag nets). Migrating fish schools are intercepted by the lead net and then led into the bag net through the pound net and funnel net. This setnet has a distinctive feature on the right side: a submerged bag net is attached to the end of a bag net open at the sea surface.The soft-type turtle releasing device (Soft-TRD) was attached to the center of the ceiling netting of the submerged bag net on the right side in the operational test. The ceiling netting was formed in a pyramid shape with about 20 degrees incline on the long sides and 50 degrees incline on the short sides toward the apex by the buoyancy of the Soft-TRD, just forming the turtle releasing system. The cover net with a height of 8 m was installed to confirm the success or failure of the escape of the sea turtle and the catch loss from this device. The upper part covered with a ceiling netting was kept at the sea surface, so the successfully escaped turtles could breathe in it.

In this study, a new type of TRD, soft-type turtle releasing device(Soft-TRD, Fig. 2), was developed without a solid frame. The Soft-TRD was designed with a slit (escape outlet) at the center of a 2 m ×2 m netting, and a float was attached to both ends of this escape slit. When the turtles push the escape slit upward, it opens, allowing them to escape. The buoyancy of the float lifts both ends of the escape slit, causes the escape slit to close. Furthermore, the nettings on both edges of the escape slit are overlaid to keep the outlet closed, even if the slit is pulled slightly due to waves or tidal currents.

One important factor considered for the design of the Soft-TRD was setting the escape slit closing force. The force could change with the buoyancy of the attached float. A higher closing force might prevent fish from escaping, but turtles might not be able to escape. The length of the escape slit and the width of overlay were also considered, and it was determined that there is a tradeoff relation between catch loss and turtle escape. Hence, a turtle releasing trial was conducted in an outdoor water tank using an experimental bag net with a mounter Soft-TRD to determine the three important design elements (i.e., float buoyancy, escape slit length, and overlay width). According to the specifications of the Soft-TRD, the closing force of the escape slit, the success rate of escape,and behavior of the turtles were examined. Moreover, a sea trial was performed in a submerged bag net utilizing the Soft-TRD to evaluate the effectiveness of this device in open water.

2.Materials and methods

2.1.Turtle releasing trial

A turtle releasing trial was conducted in an outdoor water tank(length ×width ×depth =10 m ×10 m ×2.2 m) at the Research Center for Subtropical Fisheries, Seikai National Fisheries Research Institute,Japan Fisheries Research and Education Agency (JFREA), on Ishigaki Island, Japan, between August 25 and September 5, 2017. An experimental bag net was used (length ×width ×high =3 m ×3 m ×1.6 m)with the Soft-TRD mounted at the center part of the ceiling (Fig. 2). Four loggerhead turtles (standard carapace length (SCL): 67.1–72.8 cm),which were caught in the setnets where the bag net was open at the sea surface in Mie Prefecture, and five green turtles (SCL: 42.4–63.4 cm),captured in the waters near Ishigaki Island, were used for the trial(Table 1). These turtles were captured and transported to the research center about a month before the trials began. They were maintained in two tanks (length ×width ×depth =8 m or 2.6 m ×1.7 m ×0.9 m) and were fed sardines (Sardinopssp.) and seagrass (Sargassumsp.) every day until the trials. These turtles were not used in any prior experiments.

The length of the escape slit in the Soft-TRD for the trials was investigated considering the maximum size of a loggerhead turtle, which is the main turtle species caught in setnets along the coast of Japan. The circumference of the escape slit had to be larger than the trunk circumference of the turtles, because they needed to swim upward and open the escape slit. The SCL of mature loggerhead turtles (North Pacific populations) is reported to be up to 101.5 cm (Kamezaki, 2003). The relationship between the SCLxand standard carapace width (SCW)y(y=1.0608x0.9678) and body heightz(z=0.4706x1.0081) were identified(Uchida, 1967). From these equations, the SCW and the body height of the loggerhead turtle (101.5 cm in SCL) were estimated to be 92.8 cmand 49.6 cm, respectively. The trunk circumference was estimated to be 228.8 cm, assuming that the cross-sectional shape of the turtle is elliptical; this resulted in the length of the escape slit being set to 130 cm and 150 cm considering the overlay width (10 cm and 20 cm were selected)for this trial. The buoyancy of the float attached on both ends of the escape slit was selected to be 2 kgf, 4 kgf, and 8 kgf. Thus, a Soft-TRD with these measurements was used.

Table 1 Standard straight carapace length (SCL), straight carapace width (SCW), and body weight of the sea turtles used in the releasing trial.

Fig. 2.Schematic of the experimental bag net and the Soft-TRD installed on the top used in the releasing trial. The Soft-TRD consisted of the escape slit overlaid by the net of both edges of this slit each other and the floats attached at each end of the slit.

As we proceeded with the trials, the turtles found it difficult to escape when the escape slit length was 130 cm and when the overlaying width was 20 cm. Hence, only the models with 4 kgf float for these slit lengths and overlay width were examined. A total of six models were selected for the trials (Table 2). To detect the push-up position of the turtles during the trial, a rope was attached so that the netting of each model was divided into 25 cm ×25 cm square blocks.

A single turtle was placed into the bag net, and its behavior was recorded by two video cameras from lateral (Everio GZ-R300;JVCKENWOOD. Co., Kanagawa, Japan) and overhead (PIXPRO SP360;Kodak Japan Ltd., Tokyo, Japan) perspectives. The frequency of the turtle’s push-up for each block was obtained from the video images of the overhead point of view. Effect of the model specification and the turtle size on the duration from the first push-up to escape was examined by the two-way ANOVA test, because the behavior after the first push-up is important to the success of escape (Shiozawa, Shiode, Okuyama, Hu,& Tokai, 2019).

This trial was performed twice for each individual (nine turtles) in each model (six models), resulting in a total of 108 trials. The trials were conducted only in the daytime and the same turtle was not used more than once a day. Divers were on standby at the edge of the tank during the trial to rescue the turtle in an emergency. In case the turtle in the bag net began to swim up frantically for more than 10 min, the observation was terminated, and the turtle was released out of the bag net to prevent suffocation (Shiozawa, Shiode, Okuyama, Hu, & Tokai, 2019). Previous studies confirm that divers at the edge of a tank have little effect on the behavior of turtles (Shiode et al., 2011; Tamura et al., 2014). After all the trials are complete, the turtles’ condition was observed for a week,and then they were released. This trial was approved by the Institutional Animal Care and Use Committees of both JFREA (permission No.2017–002) and Tokyo University of Marine Science and Technology(permission No. H27-2).

2.2.Measurement of the closing force of the escape slit

A tension meter (ZP-1000N; IMADA. Co., Aichi, Japan) was connected to the center of the escape slit with a wire rope (1 mm in diameter), and the closing force was measured when it was pulled horizontally. The pulling distance was set between 10 and 40 cm (at 10 cm intervals) based on the opening state of the escape slit determinedwhen the turtles escaped in the trials. The effect of float buoyancy and pulling distance on the closing force was evaluated by the two-way ANOVA test.

Table 2 Results of the releasing trial according to the specifications of the Soft-TRD.

2.3.Operational test of the setnet with the Soft-TRD

An operational test of the Soft-TRD was performed in a setnet in Mie Prefecture, Japan, from July to September 2017 (Fig. 1). The Soft-TRD(model: 150 cm escape slit length, 10 cm of the escape slit overlay,and 4 kgf buoyancy of each float; referred to as 150-10-4), which all individuals successfully escaped during the release trial, was attached to the center of the ceiling netting of the submerged bag net (30 m ×10 m×10 m; refer to Shiozawa, Shiode, Hu, Tokai, & Hirai, 2018 for the setnet details), so that the escape slit was parallel to the direction of the short side (Fig. 1). A cover net (3.2 m ×5.6 m ×8.0 m, mesh size of 33 mm) was installed surrounding the Soft-TRD to check for the presence of the escaped species through the Soft-TRD (Fig. 1). The upper part was covered with a ceiling netting, and floats were attached to keep it at the sea surface, so the successfully escaped turtles could breathe. A time-lapse camera (TLC200; Brinno Inc., Taipei, Taiwan) without any artificial lights was installed on the inside edge of the escape slit of the Soft-TRD towards the opposite end of the slit. A depth logger (DEFI-D20;JFE Advantech Co., Ltd., Tokyo, Japan) was attached beside the camera.Daytime images and depth data were taken at 1 s intervals.

3.Results

3.1.Closing force of the escape slit in the Soft-TRD

The closing force of the escape slit increased exponentially when the distance pulled horizontally increased, for each model of the Soft-TRD(Fig. 3). This force significantly varied with the buoyancy of the floats attached at each end of the escape slit and the length of the escape slit(the two-way ANOVA test,p<0.05). A greater force was required to open the escape slit with greater buoyancy of floats or shorter lengths.

3.2.Success of escaping (releasing trial)

After entering the bag net, the turtles swam at an almost constant speed along the side and the ceiling of the bag net, for approximately 5 min. Loggerhead turtles continued to swim, although green turtles occasionally tended to rest at the bottom. The turtles sometimes approached the Soft-TRD by swimming around the ceiling netting, but as they did not need to breathe, they swam back down to the bottom. As time elapsed, the turtles started to push up the ceiling netting frequently and reached the Soft-TRD. As the turtles pushed up the escape slit located at the top frequently, they successfully escaped out of the bag net(Fig. 4). The trials that did not lead to escape within the set condition were stopped, and the turtles were released by the divers.

Fig. 3.Relationship between the horizontally pulled distance and the closing force of the escape slit of the Soft-TRD according to the buoyancy of the float attached to the both end of the escape slit. Solid line shows the length of the escape slit of 150 cm, and the broken line shows 130 cm.

The mean duration (±SD) from the first push-up to escape in success trials was 28.1 ±21.1 s. There was no significant difference in these durations according to the specifications of the models and the size of the sea turtles (the two-way ANOVA test,p>0.05). Therefore, there might have been no learning effect of the turtles on the results.

The results of escaping are shown in Table 2, according to each of the specifications for the Soft-TRD. The turtles escaped successfully in all 18 trials of the 150-10-4 model. The models with the 130 cm escape slit(130-10-4 and 130-20-4) showed lower success rates when compared to 150 cm models. In addition, the success rate was lower when the overlay width was 20 cm, rather than 10 cm, when keeping the same float buoyancy and escape slit length. The smallest individual (G5, of the green turtles) was not able to escape the 20 cm overlay models.

3.3.Behavior of the turtles in escaping

The behavior of the turtles opening the escape slit was classified into two patterns, (1) lifting-up, to open the escape slit by pushing upward,and (2) expanding the escape slit with their fore flippers (Fig. 5). The frequency at which a turtle escaped by lifting-up was related to the float buoyancy. In the case of the 2 kgf float, escape by lifting-up was 56% of the total; this increased to 72% for the 4 kgf float and 88% when the buoyancy was 8 kgf (Fig. 6). The rate of escape by lifting-up was higher for larger buoyancy floats.

3.4.Cause of escape failure

The smallest individual (G5, of the green turtle species) was unable to escape during one of the two trials for the 8 kgf float model and for all trials of the 2 kgf models. The video images (8 kgf float model) show that G5 could not open the escape slit enough, even when the escape slit was pushed up. Therefore, it was considered that the closing force of the 8 kgf model was too large for smaller turtles. Further, in the 2 kg model,G5 could not reach the slit. The heads of the turtle was buried in the netting of the 2 kgf models when pushed up, because the netting tension was weak. As a result, G5 couldn’t be guided to the escape slit, because the turtle pushed up the same block of the netting many times. Hence,the frequency of consecutive push-ups at the same block for G5 was investigated (Fig. 7). A total of nine trials with more than six consecutive push-ups in the 2 kgf model were observed, but this was not the case for the 4 kgf and 8 kgf models. This may be one reason why it was difficult for the turtle to reach the escape slit in the 2 kgf model.

Fig. 4.Example of success in escaping of the loggerhead turtle through the Soft-TRD. The turtle made consecutive push-ups and successfully escaped out of the experimental bag net.

3.5.Operational test of the setnet with the Soft-TRD

During the operational test period, a total of eight loggerhead turtles entered the submerged bag net, seven of them successfully escaped(Table 3). An example of a successful escape is shown in Fig. 8. In this example, the loggerhead turtle approached the Soft-TRD with push-ups,opened the escape slit slightly by expanding, changed its body direction parallel to the escape slit, and escaped by lifting-up with further pushups. Additionally, it was confirmed that the escape slit closed immediately after the turtle had escaped (Fig. 8). Note that one loggerhead turtle did not escape the Soft-TRD, as it was unable to reach the escape slit.

The depth of the Soft-TRD indicated that the ceiling netting of the submerged bag net was constructed in a pyramid shape, with an incline toward the Soft-TRD from the buoyancy of the attached float. The fishermen’s operations were not interrupted by the introduction of the Soft-TRD.

4.Discussion

This study introduced a newly developed Soft-TRD for the submerged bag net of the setnets. The study confirmed that sea turtles were able to escape through this new device. In addition, the escape slit of this device closed immediately after the turtle escape, preventing the catch loss of commercial fish species. The Soft-TRD consisted of nets, ropes,and floats, which are ordinary fishing gear materials. Hence, this device did not interrupt the operational work of the fishermen. Moreover, one advantage for fishermen may be that this device only consisted of ordinary fishing gear materials and was easy to maintain.

The ceiling netting of the submerged bag net was formed in a pyramid shape during the operational test, by attaching the Soft-TRD equipped with the floats. Therefore, remaking the ceiling netting of the bag net is unnecessary when introducing the turtle releasing system.Furthermore, the introductory cost of this system is reduced, because it is only necessary to install the Soft-TRD at the center of the existing ceiling netting of the bag net.

Since the escape slit was located at the top in the Soft-TRD, the slope of the ceiling netting reached the outlet in the turtle releasing system.Consequently, the turtles that continuously pushed up toward the ceiling netting were guided to the escape slit, although one loggerhead turtle did not reach the escape slit during the operational test. The turtles that reached the escape slit were able to successfully escape.

There were two patterns for the turtles to open the escape slit: the lifting-up and the expanding actions. When the buoyancy of the float attached to both ends of the escape slit was increased, the proportion of escapes by the lifting-up action also tended to increase (Fig. 6). The buoyancy of the float was significantly related to the closing force of the escape slit (Fig. 3). When the float was set to be excessively buoyant, the closing force increased and might have led to the turtles not being able to open the escape slit. In fact, the escape slit was tightly closed in the 8 kgf models, preventing the escape of smallest turtles (G5). Conversely,when the buoyancy of the float was small, the closing force of the escape slit reduced (Fig. 3). It was initially thought that it would be easier for the turtles to escape the model with the smallest buoyancy float, because the required force to open the escape slit is less. However, in the case of the 2 kgf model, the netting of the device stretched weakly and slacked.Therefore, the turtles’ heads buried into the netting when they pushed up, resulting in more times of pushing up at the same position (Fig. 7). As a result, there were cases when the turtles did not reach the escape slit.The failure to escape for one loggerhead turtle during the operational test may have been caused by the weakened tension of the netting due to tidal currents or sea waves. To improve this, additional small floats arranged on the netting might be effective to increase the net tension without changing the netting shape.

Fig. 5.Patterns of the behavior of the sea turtle in opening the escape slit: left is the lifting-up that opens the escape slit by push-up upwards; the right is the expanding that expands the escape slit by fore flippers.

Fig. 6.The relative frequency of escaping patterns according to the buoyancy of the float attached to the escape slit. The white bar indicates the expanding,and the dotted bar indicates the lifting-up.

Fig. 7.The frequency of consecutive push-ups at the same block in the Soft-TRD for G5 according to the buoyancy of the float. Black bars indicate 2 kgf,grey bars 4 kgf, and white bars 8 kgf, respectively.

The results of the releasing trials showed that all but one attempt was successful in the loggerhead turtle, but some failed in the green turtle,especially in small individuals (G3-G5). In this study, individuals with SCL less than 60 cm were not used in loggerhead turtles. This is because such small individuals of loggerhead turtles do not inhabit in the waters around Japan except for the juveniles that have just hatched (Hatase et al., 2002; Ishihara et al., 2011). Therefore, the difference between turtle species in the results might be due to the size difference. However,there were differences between turtle species in the behavior until the need for breath increased. Hence, further analyses on the effects of interspecies differences in subsequent actions, especially push-up behavior, on the success of escape will be needed.

Table 3 Results of the operational test.

The difference in buoyancy of the float affected not only the closing force of the escape slit but also the tension of the netting near the escape slit, which might prevent successful escape. All turtles were able to escape from the 150-10-4 model in all trials. However, an appropriate design of the Soft-TRD must be considered from a comprehensive perspective, not only the closing mechanism of the escape slit and the propulsive force of the turtles (Shiozawa, Shiode, Hu, Tokai, & Hirai,2018) but also the tension of the netting, considering the effect of the tidal currents and sea waves (Ishidoya, 2002; Hwang & Shin, 2003).

In the models with same float buoyancy and escape slit length, the success rate of the escape was higher when the overlaying width was 10 cm, rather than 20 cm. The overlay was designed to prevent the escape slit from opening due to tidal current. In the operational test, there was little loss of fish catch during the test period. Through time-lapse photography, the escape slit was confirmed to be closed most of the time. However, some cases exist where the escape slit opened slightly when the ceiling of the bag net was located very close to the sea surface and was subjected to relatively fast tidal current (Ishidoya, 2002).Therefore, the effects of tidal currents and sea waves on the closing of the escape slit, especially for the bag net located near the sea surface,must be investigated.

About 90% of loggerhead turtles entrapped in the submerged bag net of the setnet successfully escaped through the Soft-TRD. Moreover, the operational work of the fishermen was not interrupted by the introduction of this device. Our results revealed that the Soft-TRD is helpful in releasing sea turtles from setnets and contributes to sea turtle conservation efforts.

Fig. 8.Consecutive photographs as an example of successful escape of the loggerhead turtle in the operational test. The loggerhead turtle approached the Soft-TRD with push-ups, and first opened the escape slit slightly by expanding, and then changed body direction to the parallel to the escape slit and escaped by the lifting-up with further push-ups. Besides, it was confirmed that the escape slit of the Soft-TRD closed immediately after the loggerhead turtle escaped.

Acknowledgements

The authors are grateful to K. Teruya and T. Shimizu, Seikai National Fisheries Research Institute for their assistance in the releasing trial. The authors also thank the fishermen of the setnet for their kind cooperation in the operational test. This study was partly supported by JSPS KAKENHI Grant Number JP15K07524.


登录APP查看全文