Effects of insoluble dietary fiber from wheat bran on noodle quality
2021-04-23MengxuLeiJihongHungXiolingTinPengZhouQiZhuLiminLiLiLiSenXioxiWng
Mengxu Lei,Jihong Hung,Xioling Tin,Peng Zhou,Qi Zhu,Limin Li,Li Li,Sen M,*,Xioxi Wng,*
a College of Food Science and Engineering,Henan University of Technology,Zhengzhou 450001,China
b College of Biological Engineering,Henan University of Technology,Zhengzhou 450001,China
ABSTRACT Benefiting from its favorable effects in promoting intestinal peristalsis,increasing satiety and reducing postprandial blood sugar,wheat bran insoluble dietary fiber(IDF)could be added to noodles to improve the nutrition value of noodle products.However,the addition of IDF usually results in an adverse effect on the quality characteristics of fiber fortified products,leading to unfavorable texture and consumption drop.It was found that IDF could weaken dough characteristics,thereby causing the quality deterioration of noodles,but the mechanism is unclear as yet.This study aimed to investigate the effects of different amounts of IDF on the texture quality and cooking quality of noodles.The water distribution,rheological properties,pasting properties and cooking properties of the noodles were determined by low-field nuclear magnetic resonance(LF-NMR),dynamic rheometer,and rapid visco-analyzer.The results of the LF-NMR showed that the increased IDF in the noodles resulted in a contraction of relaxation time and an increase in the proportion of loosely bound water.At a high amount of IDF,the water absorption and tensile distance of the noodles significantly decreased and the cooking loss rate increased,with a downward trend in peak viscosity,final viscosity and setback values.Moreover,IDF could improve the storage modulus and loss modulus of sheeted dough and enhance the texture of noodles.Furthermore,the correlations between IDF addition amounts and rheological properties as well as cooking properties were analyzed,and the results confirmed that noodles with the IDF amount of 2%-4%had higher nutrition and quality.This study provides the basis for future development and improvement of IDF-enriched health foods.
Keywords:Wheat bran Dietary fiber Water distribution Rheological properties IDF noodles
1.Introduction
As a traditional food worldwide, noodles can be prepared easily from wheat,buckwheat,rice,and many other widely available grains[1].Starch,protein,and water are considered important factors affecting the noodle-making process and noodle quality[2].However,the content of carbohydrates,lipids and additives in foods has increased to meet the consumers' requirement for more refined diets and pleasant mouthfeels,leading to an increased risk of various chronic diseases,such as obesity,hypertension,diabetes,and heart disease.Therefore,foods made from refined wheat flour are no longer considered as a healthy diet,and the development of foods with high dietary fiber(DF)content has become an effective way to improve the dietary pattern of humans.
DF can promote intestinal peristalsis, increase satiety and effectively reduce postprandial blood sugar, thus preventing many chronic illnesses,such as cardiovascular disease and constipation[3,4].Wheat bran with a high content of DF is a rich byproduct of wheat flour,and is widely used in wheat flour products for nutritional purposes.Most of the DF from wheat bran is insoluble dietary fiber(IDF)[5],which can be added into noodles to improve nutrition value of noodles.However,noodle quality problems caused by IDF and gluten fraction interactions must be given sufficient attention[6,7].Moreover,IDF leads to gluten conformation changes and makes it difficult to form detailed tight network structures[8,9].The effects of DF from wheat bran(WBDF)on the structure and aggregation properties of gluten were confirmed by the conversion between free sulfhydryl and disulfide bonds and the change of highmolecular-weight glutenin subunits[10].The water status in the wheat dough has significant effects on dough rheological behaviors and technological properties.Water is not evenly distributed among flour product constituents;bound water is favorable to the formation of the gluten network,and free water is related to dough fluidity[11,12].In sheeted dough,T21represents strongly bound water,which is considered the starch extra-granular water and water in the gluten matrix,and T22represents loosely bound water,which is considered the capillary water distributed in the matrix between the starch and gluten network in dough[11].Arabinoxylan is capable of binding and retaining water,so there is more tightly bound water in the T21population and higher proportions of free water in the wholewheat dough, while the T22population has decreased proportions and reduced gluten strength [10,13].The state of water is strongly associated with the elasticity and extensibility of dough and the textural properties of the end products.
Previous studies have fully proved that the addition of insoluble dietary fiber has a significant impact on the physical and chemical properties and quality characteristics of flour products,but there were a few systematic,comprehensive reports on the effect of noodle quality.Therefore,the purpose of this paper is to study the effects of IDF addition on texture properties and cooking quality of noodles.We performed comprehensive studies on the properties of dough,noodles and cooked noodles, such as dynamic rheology test for dough,water distribution and pasting properties determination for noodles, the cooking quality and texture properties measurement for cooked noodles,and also conducted correlation analysis to explore the mechanism of deterioration in dough induced by IDF, and determine the optimal addition of IDF for noodles.The results contribute to making a systematic and comprehensive interpretation of the effects of IDF on noodles quality and further guiding the application of IDF on high-fiber noodles.
2.Methods
2.1.Preparation of samples
IDF(purity 82.48%)was extracted from wheat bran in the laboratory according to the method of Liu et al.[14].The IDF was mixed with flour (Jinyuan Flour Mill Co.,Ltd., Zhengzhou, China) at different ratios (0%, 2%, 4%,6%,8%,10%)by using a JHMZ200 Pin Mixer(East Fude Technology Development Center, Beijing, China) with 38 mL of brine (5%, W/V).The pin mixer worked for 3 min at 104 r/min,then the dough crumbs were scraped from the wall and shaft into a bowl and stirred for an additional 4 min.After mixing,the dough crumbs were wrapped with plastic wrap and matured in a fermenting box(27°C,65%RH)for 20 min.The dough crumbs were pressed by a laboratory JMTD 168/180 Noodle Machine (East Fude Technology Development Center, Beijing, China) with a 4.5 mm rolling gap.The sheeted dough was wrapped with plastic wrap and matured for 30 min,and then pressed by a laboratory noodle machine 6 times until the thickness was(1.25±0.05)mm.The prepared sheets were then cut into strips(width 2.00 mm,thickness(1.25±0.05)mm).
2.2.Dynamic rheological properties of sheeted dough
Dynamic oscillatory measurements were carried out by using a Discovery HR-1 Rheometer (TA Instruments Inc., USA), referring to the method of Guadarrama-Lezama et al.[15], with some modifications.Frequency sweep tests were performed from 0.1 to 10 Hz to determine the storage modulus(G′),loss modulus(G′′),and tanδ(G′′/G′)as a function of frequency.
Creep and recovery tests were performed at fixed stress of τ=100 Pa in the range of proportionality of strain to stress.The creep phase lasted 150 s, and the recovery phase lasted 300 s.From these measurements,strain values were obtained as a function of time.Each experiment was performed in triplicate.
2.3.Water distribution of IDF noodles
The water distribution of the noodles was determined by Low-Field Nuclear Magnetic Resonance(LF-NMR).To obtain transverse relaxation time(T2)curves,the IDF noodles(0.8 g)were put into a nuclear magnetic tube and placed in the center of a constant-temperature permanent magnetic field frequency coil for Carr-Purcell-Meiboom-Gill pulse sequence testing.The number of sampling points was 40,000,the echo time was 0.100 ms, the number of echoes was 2,000,and four scan reiterations were acquired[16].
2.4.IDF noodle pasting properties
The IDF noodles were freeze-dried and ground to pass through a 100-μm sieve.The pasting properties were determined by a Rapid Visco Analyzer(RVA4500,Perten Instruments,New South Wales,Australia)according to American Association of Cereal Chemists(AACC)Method 76-21.The Standard 1(STD1)program was executed in the test.
2.5.Free sulfhydryl and disulfide bond content of IDF noodles
The free sulfhydryl(-SH)content of the samples was measured according to the method described by Alavi et al.[17]with some modifications.To determine the content of free sulfhydryl groups, 0.15 g of noodle powder and 4.70 g of guanidine hydrochloride were added to Tris-Gly buffer (10.40 g of Tris, 6.90 g of glycine, 1.20 g of EDTA,pH 8.0).The mixed solution was diluted to 10 mL and stirred for 30 min at 25 °C.Then, 8 mol/L urea(480.48 g of urea in Tris-Gly buffer)and 0.04 mL of Ellman's reagent(4.00 mg/mL in Tris-Gly buffer)were added into the solution.The solution was incubated for 30 min at 25 °C and then subjected to absorbance measurement at 412 nm by ultraviolet-visible(UV-Vis)spectrophotometry.At the same time, the blank value was determined by replacing the sample solution with distilled water,and each sample was determined 3 times.
The concentration of free sulfhydryl groups (μmol/g)was calculated as follows:

where, c1is the concentration of free -SH (μmol/g);A412is the absorbance at 412 nm;C is the mass concentration of sample solution(mg/mL);and D is the dilution factor for 5.02.
The disulfide bond (S-S)content was determined according to the method described by Ai et al.[18], with some modifications.First, 10 mol/L urea and βmercaptoethanol were used to determine the total free sulfhydryl content after the disulfide bond was reduced.Trichloroacetic acid(12%,W/V)was added after the solution was incubated for 1 h at 25 °C.The sample solution was then centrifuged, and the precipitate was washed with trichloroacetic acid and centrifuged.This operation was repeated twice.The final precipitate was dissolved in 8 mol/L urea and 0.06 mL of Ellman's reagent.The solution was incubated for 30 min at 25°C and then the absorbance was measured at 412 nm by UV-Vis spectrophotometry.At the same time, the blank value was determined by replacing the sample solution with distilled water,and each sample was determined 3 times.
The concentration of disulfide bonds(μmol/g)was calculated as follows:

where, c2is the concentration of total -SH (μmol/g);c is the concentration of S-S(μmol/g); A412is the absorbance at 412 nm;C is the mass concentration of the sample solution(mg/mL);and D is the dilution factor for 10.
2.6.Cooking and texture properties
The cooking loss and water absorption of the noodles were determined by AACC Method 66-50(AACC,2000).The cooking loss was measured according to the steps of cooking the noodle samples(25.00±1.00)g in 500 mL distilled water for 5 min,draining,moving the cooking water to a volumetric flask,adding distilled water to the flask to 1,000 mL, adding 100 mL homogeneous suspension to a beaker,evaporating in an air oven at 105°C to desired dryness, weighing the residue, and calculating cooking loss rate according to the following formula.The water absorption was recorded as the mass ratio of the raw and cooked noodles.

where,m1,m2,m3are the weight of noodles,empty beakers,the residue and beakers,respectively;w is the water content of the noodles.
The texture quality of the cooked noodles was measured by a TA-XT Plus Texture Analyzer(Stable Micro Systems,London, England).The noodle samples were cooked for 5 min in 500 mL of distilled water and immediately cooled for 30 s with cold distilled water.For texture profile analysis,three strips of cooked noodles were placed on a metal platform and compressed with an HDP/PFS probe at a test speed of 0.8 mm/s and 75% of the strain.For the tensile test,an A/SPR probe was used at a test speed of 2.0 mm/s and a distance of 100 mm.Analyses were repeated 5 times for each set of noodle samples.
2.7.Statistical analysis
The results of the various indicators obtained in the experiment were analyzed by using Origin 8.5 and SPSS 20.0 software(SPSS Inc.,Chicago,Illinois,USA).Analysis of variance(ANOVA)was used to determine significant differences between the results,and Duncan's test was used to compare the means at a significance level of 0.05.Finally,the correlation between the indicators was calculated by Pearson correlation analysis.
3.Results and discussion
3.1.Dynamic rheological properties of sheeted dough
3.1.1.Frequency sweep

Fig.1.Effects of IDF addition amount on the frequency sweep curves of the sheeted dough.
The behavior of each sheeted dough sample as a function of frequency sweep was presented in Fig.1,including G′,G′′,and tanδ variations.Dough viscoelasticity is associated with the network formed by hydrated gluten [19].The sheeted dough with IDF exhibited higher G′ and G′′ than the control, which may be due to IDF filling the network matrix gaps formed by gluten and starch[14].As can be seen from Fig.1,both G′and G′′were positively correlated with the addition amount of IDF,and the mobility was decreased between the protein chains in the gluten protein network[20].G′increased at a faster rate than G′′in the low range(0.1 to 1 Hz)of frequency sweep tests,but another frequency sweep range showed the opposite results,which were confirmed by the tanδ value.Since tanδ <1,it was suggested that IDF made the sheeted dough a more solid-like material.
3.1.2.Creep sweep
Creep recovery is associated with microstructural changes and reorientation of chemical bonds,and is often used to indicate the viscoelasticity of gluten and dough[21,22].Fig.2 showed the creep curve.In the creeping stage,the deformation of the samples increased with the extension of time.Moreover,in the recovery phase,deformation gradually recovered and tended to be stable after external forces were removed.With the increased IDF,the creep deformation of the samples showed a decreasing trend in both the creeping stage and the recovery stage.This may be attributed to the IDF limiting the hydration of starch and protein in the sheeted dough,resulting in higher mechanical strength,which was considerably higher than that in the control[14,23].
3.2.Water distribution of IDF noodles
LF-NMR was used to investigate the water distribution in the noodles.Two main proton populations (T21and T22)were detected.In the sheeted dough, T21represented strongly bound water,and T22represented loosely bound water.A21and A22represented the relative content of hydrogen protons and the water absorption by hydrophobic components [24].The effects of IDF addition amount on the water status of the noodles were shown in Table 1.
As the amount of IDF added increased,the transverse relaxation time of all the water states showed a decreasing tendency,but the changing trend was not significant.The T2decreased,demonstrating the change of water status in the noodles.The chemical exchange of protons from water to-OH,-NH2,or-SH groups in IDF,protein,or starch affected the distribution of water among the noodle constituents [25], and the binding force between the fiber and water was stronger, resulting in decreased T2relaxation time[8].While the proportion of strongly bound water decreased,the proportion of loosely bound water increased,and their changes were significant.Moreover,when the addition amount of IDF was 4%,the transverse relaxation time of strongly bound water was the shortest, indicating the least proportion; at this point, the loosely bound water was in the opposite state.The effects of IDF on water distribution were not markedly enhanced when the incorporation of IDF was more than 6%.Zhang et al.[26]presented similar findings in their experiment on the effects of bamboo shoot DF on moisture distribution in the dough.
3.3.Pasting properties of IDF noodles
The pasting properties of the IDF noodles were measured by a rapid viscosity analyzer(Table 2).The peak viscosity was an important indicator of the quality of cooked noodles,as it showed significantly positive correlations with stickiness,appearance,smoothness,and so on[27].The peak viscosity,trough viscosity,and final viscosity decreased with the increase of IDF,which is consistent with previous studies[28,29].The increasing of the substitution level of IDF resulted in fewer starch granules available to gelatinize.These viscosities showed a downward trend that also may be due to the IDF being more capable of binding water than starch granules, causing higher resistance to starch granule swelling[30,31].Amylopectin determines the viscosity of starch,whereas water is absorbed by IDF,so that amylopectin cannot combine with sufficient water and completely form sticky substances.The peak viscosity decreased obviously, implying the deterioration of noodle quality caused by increasing IDF amounts[28].The breakdown was obviously higher than that in the control group,though the difference was not significant.Previous studies have shown that the breakdown is negatively correlated with amylose content[32].

Fig.2.Effects of IDF addition amount on the creep recovery properties of the sheeted dough.

Table 1 Water distribution of noodles containing different amounts of IDF.

Table 2 Pasting properties of noodles containing different amounts of IDF.
The setback value is used to indicate the degree of aging caused by the reaggregation of starch granules after gelatinization,which is closely related to the degree of rearrangement and recrystallization of amylose molecules[33].The setback value showed a markedly decreasing trend with the increase of IDF content(Table 2).The decreased setback value indicated that the aging process of starch was inhibited,and the decreasing degree was positively correlated with IDF concentration.It is probably due to the physical barrier formed by IDF with high holding-water capacity,which restricted the recrystallization of amylose molecular after gelatinization,therefore inhibiting the retrogradation of starch, which is similar to the findings of Luo et al.[34].
3.4.Free sulfhydryl and disulfide bond content of IDF noodles
The conversion between free sulfhydryl and disulfide bonds plays an extremely important role in protein crosslinking polymerization,indicating the tightness of the protein spatial structure.Free sulfhydryl and disulfide bonds in gluten protein have a marked influence on dough structure formation and end product quality[35].The aggregation degree of protein was evaluated by the disulfide bond content,and free sulfhydryl content was used to confirm protein crosslinking formation during the gluten development process[36].The results were shown in Fig.3.The free sulfhydryl content was positively correlated with the amount of IDF, and there was a significant difference,while the disulfide bond content increased slightly at low IDF amounts and decreased at high IDF amounts.Increased-SH content can hinder glutenin aggregation due to the replacement of protein with IDF[37].As in previous studies,a strong correlation was found between-SH content and the formation of a proper gluten network [38].Glutenin is a main determinant of dough quality and is affected by disulfide bonds[39].
3.5.Cooking and texture properties
Water absorption and cooking loss rate are the key indexes to evaluate noodle quality during cooking.Cooking loss rate represents the amount of solid components in the noodles leaching into the water during cooking,and it indicates the degree of bonding between each ingredient in the noodles.The cooking loss rate of the noodles rose significantly with increased IDF (Table 3), which is consistent with the findings of other researchers[40].The gluten network may be weakened by DF,with amylose leaching during cooking [41].As shown in Table 3, water absorption clearly decreased with increased IDF due to the cooking loss,which is consistent with previous research[42].

Fig.3.The free sulfhydryl and disulfide bond content of noodles with various levels of IDF.
At low IDF amounts(≤4%),the springiness of the noodles gradually decreased, while their hardness and chewiness increased, and the difference was significant(Table 3).At high IDF amounts (≥6%), the changes in these indexes were not significant.The covalent and noncovalent interactions between protein and IDF can cause higher molecular mass polymerization, increasing the hardness of cooked noodles.In addition, smaller IDF particles can fill in the gaps of the gluten network structure,increasing noodle stiffness[43].However,there was a significant negative correlation between the maximum tensile distance of the noodles and the added amount of IDF,which may be due to IDF exerting binding steric hindrance,resulting in a negative impact on gluten malleability[44].
3.6.Correlation analysis
The correlations between IDF addition amounts and rheological properties as well as cooking properties were shown in Table 4.The addition amounts of IDF had a significant correlation with rheological properties,peak viscosity,setback value and cooking loss rate(P <0.05).G′and G′′is in significant positive correlation with the level of IDF(P <0.05), probably due to IDF dominating more water and leading to less lubrication[45,46].Moreover,IDF can fill in the gluten network and increase the viscoelasticity of the matrix[47].The cooking loss rate was in extremely positive relation with G′′and the addition amount of IDF(P <0.01), while it showed negative correlation with peak viscosity and tensile distance(P <0.05).It is due to IDF damaged the gluten matrix and causing the enhancement of mobility and loss rate.The hardness and tensile distance of noodles were positively and negatively correlated with the viscoelasticity of the sheeted dough,respectively.

Table 3 Cooking and texture properties of cooked noodles with different levels of IDF.
4.Conclusions
The effects of IDF on the correlated characteristics about noodle quality have been evaluated in the present study.The viscoelasticity and mechanical strength of the sheeted dough were enhanced at low IDF amounts, and this may be due to IDF filling in the gluten network, making the sheeted dough stiffer.High amounts of IDF were not conducive to the creep recovery of the sheeted dough,as IDF combined with water results in a tighter structure,which has adverse effects on gluten network formation.Furthermore,the variousness of water distribution with different levels of IDF was also confirmed by the increased proportion of loosely bound water(A22).IDF decreased the viscosity in the noodle flour pasting process,and it decreased the setback values,indicating that IDF could inhibit the retrogradation degree of cooked noodles.This may be attributed to the high water retention capacity of IDF and the formation of a hydrated layer around the starch granules.Low amounts of IDF could increase noodle chewiness and disulfide bond content,which may be beneficial to improve noodle quality.The free sulfhydryl content and cooking loss were significantly increased when noodles had amounts of IDF over 4%,while the maximum tensile distance was reduced,which are unfavorable to noodle quality.In conclusion, wheat flour with 4% IDF may be used as a theoretical reference for the production of noodles with high dietary fiber.
Author Contributions
Mengxu Lei:Conceptualization,methodology,software,writing-original draft preparation;Jihong Huang:Writing- reviewing and editing, funding acquisition; Xiaoling Tian: Methodology, software, investigation; Peng Zhou:Data curation,experiment;Qi Zhu:Data curation,experiment;Limin Li:Writing-reviewing and editing;Li Li:Visualization, investigation; Sen Ma: Supervision, writingreviewing and editing, project administration; Xiaoxi Wang:Funding acquisition,supervision.
Conflicts of Interest
The authors declare that there is no conflict of interest.

Table 4 The correlation between IDF addition amount and noodles quality.
Acknowledgment
This work was supported by Zhongyuan Scholars in Henan Province (No.192101510004), the Natural Science Foundation of China (No.31671810), Project of Green Manufacturing 2025.China(Ministry of industry and information Technology.2018-272), Strategic Consulting Research Project of Henan Institute of Chinese Engineering Development Strategies(No.2020HENZT13),and the Key scientific and technological project of Henan Province(No.202102110143).
杂志排行
Grain & Oil Science and Technology的其它文章
- Phytosterols in edible oil:Distribution,analysis and variation during processing
- Morphological and molecular identification of Xylocoris flavipes(Hemiptera:Anthocoridae)in southern China
- Study on enzymatic hydrolysis of soybean β-conglycinin using alkaline protease from Bacillus subtilis ACCC 01746 and antigenicity of its hydrolysates
- Effects of hexanal fumigation on fungal spoilage and grain quality of stored wheat
