典型钢板汽车覆盖件拉延工艺介绍
2020-02-25李科杰何星明邬波谷树华
李科杰 何星明 邬波 谷树华
摘 要:拉延是利用拉深模使平面板料变为开口空心件的冲压工序。作为典型汽车覆盖件冲压工艺的首道工序,拉延工艺的优劣将直接对汽车覆盖件外观质量以及后续的工艺设计产生影响。文章以典型钢板汽车覆盖件为研究对象,结合实际生产经验,从常用板料、冲压方向、工艺补充注意点、拉延筋四个方面详细介绍了拉延工艺设计要点,分析了拉延工序中常见质量缺陷及避免方法,对典型钢板汽车覆盖件同步工程分析、模具设计及调试等具有一定的参考价值。关键词:汽车覆盖件;拉延;板料;冲压方向;工艺补充;拉延筋中图分类号:U466 文献标识码:B 文章编号:1671-7988(2020)01-156-05
Abstract: Drawing is the process of making the flat plate into open hollow part by drawing die. As the first process of typical automobile panel stamping process, drawing process will directly affect the appearance quality of automobile panel and subsequent process design. Based on the typical steel automotive covering parts as the research object, combined with the actual production experience, from common sheet metal, pressing direction, addendum attention points, drawbead drawing process design points are introduced in detail, analyses the drawing working procedure in addendum attention points of common quality defects and avoid method, the typical steel automotive covering parts synchronous engineering analysis, mold design and debug and so on has certain reference value.Keywords: Auto panel; Draw; Material; Pressing direction; Addendum; DrawbeadCLC NO.: U466 Document Code: B Article ID: 1671-7988(2020)01-156-05
前言
伴随着汽车产业的快速发展,人们对汽车覆盖件的实用性、可靠性和美观性的要求越来越高,拉延工序作为车身覆盖件成形过程最关键的工序,其设计的是否合理将直接影响汽车覆盖件的外观质量及新车型的开发周期,因此,对汽车覆盖件拉延工序进行分析,将有利于缩短模具设计时间,提高覆盖件外观质量,从而提高企业竞争力[1-2]。
拉延工艺设计是决定汽车覆盖件能否顺利成形的关键,也是拉延模具设计与制造的基础,对产品的质量、成本、生产效率和模具的使用寿命有直接影响。汽车覆盖件拉延工艺设计过程复杂,需要不断的尝试、分析及决策,对工艺设计者的经验要求较高,设计周期较长,难度较大[3-4]。
汽车覆盖件拉延工艺设计主要包括五个方面,分别为板料的选取、冲压方向的设定、压边圈的设计、工艺补充的设计、拉延筋的设计,每一个方面均会影响最终拉延件成形质量,因压边圈的设计大多随冲压件的形状,在此不再赘述。……
