Nonlinear Bending and Thermal Post-Buckling Analysis of FGM Beams Resting on Nonlinear Elastic Foundations
2014-04-16DaGuangZhangandHaoMiaoZhou
Da-Guang Zhang and Hao-Miao Zhou
1 Introduction
Functionally graded materials(FGMs)are a class of novel materials in which properties vary continuously in a specific direction.To withstand the high-temperature effects,generally FGM structures made of ceramic and metal constituents are addressed.Consequently,investigations on behaviors of FGM structures are identified as an interesting field of study in recent years.
Many investigations on the linear bending and buckling of FGM or laminated or homogeneous beams can be seen in[Sankar(2001);Venkataraman and Sankar(2003);Zhong and Yu(2007);Ying et al.(2008);Giunta et al.(2010);Aminbaghai et al.(2012);Giunta et al.(2013);Dong et al.(2013);Dong et al.(2014);Elgohary etal.(2014)].And lotsofstudieshave been also made on the nonlinearbending and post-buckling of FGM beams based on Euler-Bernoulli beam theory,Timoshenko beam theory and higher order shear deformation beam theory.However,relatively few have been made on the nonlinear analysis of FGM beams resting on elastic foundations.Among those,Zhang(2013,2014)put forward a model of the FGM beams based on physical neutral surface and high order shear deformation theory,and analyzed nonlinear bending,thermal post-buckling and nonlinear vibration behaviors by Ritz method.Ma and Lee(2011)derived governing equations for both the static behavior and the dynamic response of FGM beams subjected to uniform in-plane thermal loading,based on the physical neutral surface and the first order shear deformation beam theory,then Ma and Lee(2012)gave exact solutions for nonlinear static responses of a shear deformable FGM beam under an in-plane thermal loading.Li et al.(2006)studied thermal post-buckling of functionally graded material Timoshenko beams.Almeida et al.(2011)presented geometric nonlinear analysis formulation for beams of functionally graded cross-sections by means of a total Lagrangian formulation.Rahimi and Davoodinik(2010)discussed the large deflection of a functionally graded cantilever beam under inclined end loading by fully accounting for geometric nonlinearities using analytical and Adomian decomposition methods,then Davoodinik and Rahimi(2011)extended their works to a flexible tapered functionally graded cantilever beam.Rahimi et al.(2013)investigated the post-buckling behavioroffunctionally graded beamsby meansofan exact solution method.Zhao et al.(2007)derived the non-linear differential equations of post-buckling for FGM rod subjected to thermal load.They considered rods with both ends pinned and used the shooting method to solve the equations.Fu et al.(2012)discussed nonlinear analysis of buckling,free vibration and dynamic stability for the piezoelectric functionally graded beams in thermal environment.Ke et al.(2009)studied post-buckling behavior of functionally graded material beams including an edge crack effect based on Timoshenko beam theory and von-Kármán’s strain–displacement relations.They applied the Ritz method to obtain the non-linear governing equations and used the Newton-Raphson method to obtain the postbuckling load-end shortening curves and post-buckling de flection-end shortening curves.Anandrao et al.(2010)investigated the buckling and thermal post-buckling behavior of uniform slender FGM beams.The von-Kármán strain–displacement relationship is used to obtain the equations.Single-term Ritz method and finite elements method are applied to obtain the response of the beam.Then Anandrao et al.(2012)studied large amplitude free vibration and thermal postbuckling of shear flexible FGM beams using finite element formulation based on first order Timoshenko beam theory.Ansari et al.(2013)investigated thermal post-buckling characteristics of FGM microbeams undergoing thermal loads based on the modi fied strain gradient theory.Shegokar and Lal(2013)provided the stochastic nonlinear bending response of FGM beam with surface bonded piezoelectric layers subjected to thermo-electro-mechanical loadings with uncertain material properties.Shen and Wang(2014)dealt with the large amplitude vibration,nonlinear bending and thermal postbuckling of FGM beams resting on an elastic foundation in thermal environments.Fallah and Aghdam(2011,2012)investigated nonlinearfree vibration and post-buckling analysisoffunctionally graded beamson nonlinear elastic foundation.Esfahani et al.(2013)examined thermal buckling and post-buckling analysis of FGM Timoshenko beams resting on a non-linear elastic foundation.Ghiasian et al.(2013)studied static and dynamic buckling of an FGM beam resting on a non-linear elastic foundation subjected to uniform temperature rise loading and uniform compression.
The present paper extends the previous works[Zhang(2013);Zhang(2014)]to nonlinear bending and thermal post-buckling analysis of FGM beams resting on nonlinear elastic foundations based on physical neutral surface and high order shear deformation theory.Temperature dependent material properties and von Kármán strain-displacement relationship are taken into consideration.The material properties of FGMs are assumed to be graded in thickness direction according to a volume fraction power law distribution and are expressed as a nonlinear function of temperature.Approximate solutions of FGM beams are obtained by Ritz method.
2 Temperature dependent material properties of FGM beams

Figure 1:Geometry and coordinates of a FGM beam resting on nonlinear elastic foundations.
Consider a FGM beam(thicknesshand lengthLx)with rectangular cross-section,which is made from a mixture of metals and ceramics.The coordinate system is illustrated in Fig.1.It can be assumed that the effective material propertiesPof FGMs,such as Young’s modulusE,Poisson’s ratioν,thermal conductivityκand thermal expansion coefficientα,can be expressed as

in whichVmandVcare the metal and ceramic volume fractions and are related byVm+Vc=1,PmandPcdenote the temperature-dependent properties of metal and ceramic beam,respectively,and may be expressed as a nonlinear function of temperature[Touloukian(1967)]

in whichT=T0+∆TandT0=300 K(room temperature),P−1,P0,P1,P2andP3are the coefficients of temperatureT(K)and are unique to the constituent materials.
3 Modeling of FGM beams resting on nonlinear elastic foundations based on physical neutral surface and high order shear deformation theory
As is customary,the foundation is assumed to be a compliant foundation,meaning no part of the beam lifts off the foundation in the deformed region.The loaddisplacementrelationship of the foundation is assumed to bep=K1w−K2d2w/d x2+K3w3,wherepis the force per unit area,K1is the Winkler foundation stiffness,K2is a constant showing the effect of the shear interactions of the vertical elements andK3is nonlinear elastic foundation coefficients.
According to model of FGM beams[Zhang(2013);Zhang(2014)]based on physical neutral surface and high order shear deformation theory,the displacements,the strains and the stresses have the same form as the previous works[Zhang(2013);Zhang(2014)],see Appendix A.1-8.For the sake of brevity,the deducing process of the formulae is omitted,and the governing equations can be derived according to energy variational principle.

And if the boundaries have no in-plane displacements on the geometric middle plane,i.e.prevented from moving in thex-direction,Nxcan then be written in integral form as

All symbols used in Eq.(3)are defined by Zhang(2013,2014),see Appendix A.9.In the following analysis,two cases of boundaries will be considered.

4 Ritz method for approximate solutions of nonlinear problems of FGM beams
Ritz method is adopted in this section to obtain approximate solutions of FGM beams,and in symmetrical problems about the beams with immovable simply supported ends,it can be assumed that

whereMis total number of series,and whereaiare undetermined coefficients.We assume that the temperature variation is uniform and occurs in the thickness direction only,i.e.NT,MTandPTare constants for FGM beams,so substituting Eq.(5a)into Eq.(3a),ψxcan be determined as

For symmetrical problems about the beam with immovable clamped ends,it can be assumed that


Cubic algebraic equations aboutaican be obtained by substitutingwandψxinto the following expression.

in which Π=U+V,in which the strain energyUis

where Ω denotes domain of FGM beams.Work done by applied forcesVis

As for FGM beams with given loads(like transverse uniformly distributed loadsq0and thermal loadsNT,MT,PT)and other known coefficients,aican be solved by Newton-Raphson iterative method or other equivalent methods.For the sake of brevity,nonlinear algebraic equations and the solving process are omitted.Substituting these coefficients back into Eqs.(5)and(7),wandψxmay then be completely determined.In addition,if critical thermal buckling loads exist,critical value can be easily obtained by making solutions of deflection coefficientsaiapproach to zero.
In addition,the present paper extends convergence studies of the previous works[Zhang(2013)]to nonlinear bending and thermal post-buckling analysis of FGM beams resting on nonlinear elastic foundations,soM=3 is also used in all the following calculations.
5 Results and discussions
Numerical results are presented in this section for nonlinear bending and thermal post-buckling of FGM beams.A Si3N4/SUS304 is selected as an example.Typical values for Young’s modulusE(in Pa),Poisson’s ratioν,thermal expansion coefficientα(in K−1)and thermal conductivityκ(in W/mK)are listed in Table 1 from Reddy and Chin(1998).One dimensional temperature field is assumed to be constant in thex−yplane of the layer.In such a case,the temperature distribution along the thickness can be obtained by solving a steady-state heat transfer equation

This equation can be solved by imposing boundary condition ofT=Ttat the top surface(z=−h/2)andT=Tbat bottom surface(z=h/2).The solution of this equation is

Note that the temperature field is uniform whenTt=Tb.

Table 1:Temperature-dependent coef ficients for ceramic and metals[Reddy and Chin(1998)].
5.1 Comparison studies
To ensure the accuracy and effectiveness of the present method,two examples are solved for nonlinear bending and thermal post-buckling analysis of isotropic and FGM beams.


Table 2:Comparisons of nonlinear bending for isotropic beams resting on different elastic foundations.

Figure 2:Comparisons of thermal post-buckling for Si3N4/SUS304 beams with immovable clamped ends resting on different elastic foundations subjected to uniform temperature rise.

Figure 3:Comparisons of thermal post-buckling for Si3N4/SUS304 beams with immovable simply supported ends resting on different elastic foundations subjected to heat conduction.
Example 2.Thermal post-buckling for Si3N4/SUS304 beams with different supported ends resting on different elastic foundations are calculated and compared in Figs.2 and 3 with results of Esfahani et al.(2013)using generalized differential quadrature method.In this example,length to thickness ratioLx/h=25,volume fraction indexN=1,and the dimensionless foundation stiffnesses are(k1,k2,k3)=(100,0,0)forthe Winklerelastic foundation,(k1,k2,k3)=(100,10,0)for the Pasternak elastic foundation,(k1,k2,k3)=(100,0,50)and(k1,k2,k3)=(100,10,50)for the nonlinear elastic foundation,wherek1=12K1Lx4/E0h3,k2=12K2Lx2/E0h3andk3=12K3Lx4/E0h,E0is Young’s modulus of Si3N4at reference temperature.Excellent agreements can be seen from Figs.2 and 3.
5.2 Parametric studies
Aparametric study wasundertaken fornonlinearbending and thermalpost-buckling of Si3N4/SUS304 beams withLx/h=50.The volume fractionVcis defined byVc=(1/2−z/h)N,and the dimensionless foundation stiffnesses are(k1,k2,k3)=(50,0,0)for the Winkler elastic foundation,(k1,k2,k3)=(50,5,0)for the Pasternak elastic foundation,(k1,k2,k3)=(50,0,10)and(k1,k2,k3)=(50,5,10)for the nonlinear elastic foundation,wherek1=K1L4x/E0h3,k2=K2L2x/E0h3andk3=K3L4x/E0h,E0is Young’s modulus of SUS304 at reference temperature.The top surface is ceramic-rich,whereas the bottom surface is metal-rich,henceTt=TcandTb=Tmfor heat conduction.

Figure 4:Effect of volume fractions on nonlinear bending of Si3N4/SUS304 beams with immovable simply supported ends resting on nonlinear elastic foundations.
The central dimensionless deflections of Si3N4/SUS304 FGM beams with immovable simply supported ends and clamped ends subjected to transverse uniformly distributed loads in different temperature fields are calculated,see Figs.4-9.The effect of volume fractions on nonlinear bending of Si3N4/SUS304 beams with different supported ends resting on nonlinear elastic foundations can be seen in Figs.4,5,it can be observed that the deflections increase with increasing value of volume fraction indexN.The effect of different elastic foundations on nonlinear bending of Si3N4/SUS304 beams with different supported ends and volume fraction indexN=2 can be seen in Figs.6,7,it can be observed that the effect of nonlinear elastic foundation increase with increasing de flection.The effect of different temperature fields on nonlinear bending of Si3N4/SUS304 beams with different supported ends and volume fraction indexN=2 resting on nonlinear elastic foundations can be seen in Figs.8,9,downward initial de flections under uniform temperature rise fields and the upward initial de flections under heat conduction fields can be observed for the beams with immovable simply supported ends,while no initial deflections under both uniform temperature rise and heat conduction fields can be observed for the beams with immovable clamped ends.

Figure 5:Effect of volume fractions on nonlinear bending of Si3N4/SUS304 beams with immovable clamped ends resting on nonlinear elastic foundations.

Figure 6:Effect of elastic foundations on nonlinear bending of Si3N4/SUS304 beams with immovable simply supported ends.

Figure 7:Effect of elastic foundations on nonlinear bending of Si3N4/SUS304 beams with immovable clamped ends.

Figure 8: Effect of different temperature fields on nonlinear bending of Si3N4/SUS304 beams with immovable simply supported ends.

Figure 9: Effect of different temperature fields on nonlinear bending of Si3N4/SUS304 beams with immovable clamped ends.

Figure 10:Thermal post-buckling behaviors for Si3N4/SUS304 beams with immovable simply supported ends resting on nonlinear elastic foundations subjected to uniform temperature rise.

Figure 11:Thermal post-buckling behaviors for Si3N4/SUS304 beams with immovable simply supported ends resting on nonlinear elastic foundations subjected to heat conduction.

Figure 12:Thermal post-buckling behaviors for Si3N4/SUS304 beams with immovable clamped ends resting on nonlinear elastic foundations subjected to uniform temperature rise.

Figure 13:Thermal post-buckling behaviors for Si3N4/SUS304 beams with immovable clamped ends resting on nonlinear elastic foundations subjected to heat conduction.

Figure 14:Effect of elastic foundations on thermal post-buckling of Si3N4/SUS304 beams with immovable simply supported ends subjected to uniform temperature rise.

Figure 15:Effect of elastic foundations on thermal post-buckling of Si3N4/SUS304 beams with immovable simply supported ends subjected to heat conduction.

Figure 16:Effect of elastic foundations on thermal post-buckling of Si3N4/SUS304 beams with immovable clamped ends subjected to uniform temperature rise.

Figure 17:Effect of elastic foundations on thermal post-buckling of Si3N4/SUS304 beams with immovable clamped ends subjected to heat conduction.
Thermal post-buckling behaviors for Si3N4/SUS304 FGM beams with different supported ends resting on nonlinear elastic foundations subjected to uniform temperature rise and heat conduction are calculated,see.Figs.10-13.Bifurcation of buckling can occur for FGM beams with simply supported ends due to effect of uniform temperature rise or heat conduction,while bifurcation of buckling can not occur for FGM beams with clamped ends due to effect of uniform temperature rise and heat conduction.The effect of elastic foundations on thermal post-buckling of Si3N4/SUS304 beams with different supported ends and volume fraction indexN=2 resting on nonlinear elastic foundations subjected to uniform temperature rise and heat conduction are calculated,see.Figs.14-17,and it can be observed that the effect of nonlinear elastic foundation increase with increasing deflection.
6 Conclusions
A model of the FGM beams resting on nonlinear elastic foundations is successfully established by physical neutral surface and high-order shear deformation theory.In nonlinear bending and post-buckling analysis,influences played by different supported boundaries,thermal environmental conditions,different elastic foundation and volume fraction index are discussed in detail.In nonlinear bending analysis,downward initial deflections under uniform temperature rise fields and the upward initial deflections under heat conduction fields can be observed for the FGM beams with immovable simply supported ends,while no initial deflections under both uniform temperature rise and heat conduction fields can be observed for the FGM beams with immovable clamped ends.In thermal post-buckling analysis,bifurcation of buckling can occur for FGM beams with simply supported ends due to effect of uniform temperature rise or heat conduction,while bifurcation of buckling can not occur for FGM beams with clamped ends due to effect of uniform temperature rise and heat conduction.It is worth noting that the effect of nonlinear elastic foundation is significant with increasing deflection.
Acknowledgement:This research was supported by the Fund of the National Natural Science Foundation of China under Grant No.11172285,and Zhejiang Provincial Natural Science Foundation of China under Grant No.LR13A020002.The authors would like to express their sincere appreciation to these supports.
Almeida,C.A.;Albino,J.C.R.;Menezes,I.F.M.;Paulino,G.H.(2011):Geometric nonlinear analyses of functionally graded beams using a tailored Lagrangian formulation.Mech.Res.Commun.,vol.38,pp.553-559.
Aminbaghai,M.;Murín,J.;Kutiš,V.(2012):Modal analysis of the FGM-beams with continuous transversal symmetric and longitudinal variation of material properties with effect of large axial force.Eng Struct,vol.34,pp.314-329.
Anandrao,K.S.;Gupta,R.K.;Ramchandran,P.;Rao,G.V.(2010):Thermal post-buckling analysis of uniform slender functionally graded material beams.Struct.Eng.Mech.,vol.36,pp.545-560.
Anandrao,K.S.;Gupta,R.K.;Ramchandran,P.;Rao,G.V.(2012):Nonlinearfree vibrations and post-buckling analysisofshearflexible functionally graded beams.Struct.Eng.Mech.,vol.44,pp.339-361.
Ansari,R.;Faghih-Shojaei,M.;Gholami,R.;Mohammadi,V.;Darabi,M.A.(2013):Thermal postbuckling behavior of size-dependent functionally graded Timoshenko microbeams.Int.J.Nonlin.Mech.,vol.50,pp.127-135.
Davoodinik,A.R.;Rahimi,G.H.(2011):Large deflection of flexible tapered functionally graded beam.Acta Mech.Sinica,vol.27,pp.767-777.
Dong,L.;El-Gizawy,A.S.;Juhany,K.A.;Atluri,S.N.(2014):A simple locking-alleviated 4-node mixed-collocation finite element with over-integration,forhomogeneousorfunctionally-graded orthick-section laminated composite beams.CMC-Comput.Mater.Con.,vol.40,pp.49-76.
Dong,L.;Gamal,S.H.;Atluri,S.N.(2013):Stochastic macro material properties,through direct stochastic modeling of heterogeneous microstructures with randomness of constituent properties and topologies,by using Trefftz computational grains.CMC-Comput.Mater.Con.,vol.37,pp.1-21
Elgohary,T.A.;Dong,L.;Junkins,J.L.;Atluri,S.N.(2014):Solution of post-buckling&limit load problems,without inverting the tangent stiffness matrix&without using arc-length methods.CMES-Comp.Model.Eng.,vol.98,pp.543-563.
Esfahani,S.E.;Kiani,Y.;Eslami,M.R.(2013):Non-linear thermal stability analysis of temperature dependent FGM beams supported on non-linear hardening elastic foundations.Int.J.Mech.Sci.,vol.69,pp.10-20.
Fallah,A.;Aghdam,M.M.(2011):Nonlinear free vibration and post-buckling analysis of functionally graded beams on nonlinear elastic foundation.Eur.J.Mech.A-Solid,vol.30,pp.571-583.
Fallah,A.;Aghdam,M.M.(2012):Thermo-mechanical buckling and nonlinear free vibration analysis of functionally graded beams on nonlinear elastic foundation.Compos.Part B-Eng.,vol.43,pp.1523-1530.
Fu,Y.M.;Wang,J.Z.;Mao,Y.Q.(2012):Nonlinear analysis of buckling,free vibration and dynamic stability for the piezoelectric functionally graded beams in thermal environment.Appl.Math.Model.,vol.36,pp.4324-4340.
Ghiasian,S.E.;Kiani,Y.;Eslami,M.R.(2013):Dynamic buckling of suddenly heated or compressed FGM beams resting on non-linear elastic foundation.Compos.Struct.,vol.106,pp.225-234.
Giunta,G.;Belouettar,S.;Carrera,E.(2010)Analysis of FGM beams by means of classical and advanced theories.Mech Adv Mater Struct,vol.17,pp.622-635.
Giunta,G.;Crisafulli,D.;Belouettar,S.;CarreraE.;(2013)Athermo-mechanical analysis of functionally graded beams via hierarchical modeling.Compos Struct,vol.95,pp.676-690.
Horibe,T.;Asano,N.(2001):Large deflection analysisofbeamson two-parameter elastic foundation using the boundary integral equation method.JSME International Journal,vol.44,pp.231-236.
Ke,L.L.;Yang,J.;Kitipornchai,S.(2009):Postbuckling analysis of edge cracked functionally graded Timoshenko beams under end shortening.Compos.Struct.,vol.9,pp.152-160.
Li,S.R.;Zhang,J.H.;Zhao,Y.G.(2006):Thermalpost-buckling offunctionally graded material Timoshenko beams.Appl.Math.Mech.,vol.27,pp.803-810.
Ma,L.S.;Lee,D.W.(2011):A further discussion of nonlinear mechanical be-havior for FGM beams under in-plane thermal loading.Compos.Struct.,vol.93,pp.831-842.
Ma,L.S.;Lee,D.W.(2012):Exact solutions for nonlinear static responses of a shear deformable FGM beam under an in-plane thermal loading.Eur.J.Mech.A-Solid,vol.31,pp.13-20.
Rahimi,G.H.;Davoodinik,A.R.(2010):Large deflection of functionally graded cantilever flexible beam with geometric nonlinearity:analytical and numerical approaches.Sci.Iran B-Mech.Eng.,vol.17,pp.25-40.
Rahimi,G.H.;Gazor,M.S.;Hemmatnezhad,M.;Toorani,H.(2013):On the postbuckling and free vibrations of FG Timoshenko beams.Compos.Struct.,vol.95:pp.247-253.
Reddy,J.N.;Chin,C.D.(1998):Thermoelastical analysis of functionally graded cylinders and plates.J.Therm.Stresses,vol.21,pp.593-626.
Sankar,B.V.(2001):An elasticity solution for functionally graded beams.Compos Sci Technol,vol.61,pp.689-696.
Shegokar,N.L.;Lal,A.(2013):Stochastic nonlinear bending response of piezoelectric functionally graded beam subjected to thermoelectromechanical loadings with random material properties.Compos.Struct.,vol.100,pp.17-33.
Shen,H-S.;Wang,Z.-X.(2014):Nonlinear analysis of shear deformable FGM beams resting on elastic foundations in thermal environments.Int.J.Mech.Sci.,vol.81,pp.195–206.
Touloukian,Y.S.(1967):Thermophysical properties of high temperature solid materials,first ed.Macmillan,New York.
Venkataraman,S.;Sankar,B.V.(2003):Elasticity Solution for Stresses in a Sandwich Beam with Functionally Graded Core.AIAA J,vol.41,pp.2501-2505.
Ying,J.;Lü C.F.;Chen,W.Q.(2008):Two-dimensional elasticity solutions for functionally graded beams resting on elastic foundations.Compos Struct,vol.84,pp.209-219.
Zhang,D.-G.(2013):Nonlinear bending analysis of FGM beams based on physical neutral surface and high order shear deformation theory.Compos.Struct.,vol.100,pp.121-126.
Zhang,D.-G.(2014):Thermal post-buckling and nonlinear vibration analysis of FGM beams based on physical neutral surface and high order shear deformation theory.Meccanica,vol.49,pp.283-293
Zhao,F.Q.;Wang,Z.M.;Liu,H.Z.(2007):Thermal post-buckling analyses of functionally graded material rod.Appl.Math.Mech.,vol.28,pp.59-67.
Zhong,Z.;Yu,T.(2007)Analytical solution of a cantilever functionally graded beam.Compos Sci Technol,vol.67,pp.481-488.
Appendix A
The displacement fields

in whichz0andc0are defined by

Considering nonlinear von Kármán strain-displacement relationships,the strains can be expressed by

According to Hooke’s law,the stresses can be determined as

The constitutive equations can be deduced by proper integration.


In which the beam stiffnesses are defined by

The axial forces,bending moments and higher order bending moment caused by elevated temperature are defined by

where∆T=T−T0istemperature rise from some reference temperatureT0atwhich there are no thermal strains.
The symbols used in the governing equations are defined by

