Reliability sensitivity analysis based on multi-hyperplane combination method
2014-02-15YugeDONGHaitaoLUbLinglingLI
Yu-ge DONG*,Hai-tao LUb,Ling-ling LI
aSchool of Mechanical and Automotive Engineering,Hefei University of Technology,Hefei 230009,Anhui,China
bSchool of Machinery Engineering,Huaiyin Institute of Technology,Huai'an 223003,Jiangsu,China
cProvince-Ministry Joint Key Laboratory of Electromagnetic Field and Electrical Apparatus Reliability,Hebei University of Technology,Tianjin 300130,China
Reliability sensitivity analysis based on multi-hyperplane combination method
Yu-ge DONGa,*,Hai-tao LUa,b,Ling-ling LIc
aSchool of Mechanical and Automotive Engineering,Hefei University of Technology,Hefei 230009,Anhui,China
bSchool of Machinery Engineering,Huaiyin Institute of Technology,Huai'an 223003,Jiangsu,China
cProvince-Ministry Joint Key Laboratory of Electromagnetic Field and Electrical Apparatus Reliability,Hebei University of Technology,Tianjin 300130,China
For a nonlinear limit state function,the frst-order reliability method(FORM)may cause large errors in the computation of not only the reliability index or failure probability but also the reliability sensitivity.In order to obtain more the accurate results of the reliability sensitivity analysis,a number of hyperplanes are built near the design point by frst-order Tayler series expansion,which replace the known nonlinear limit state hypersurface,and an equivalent computational method is utilized to construct an equivalent hyperplane of the obtained hyperplanes.And the reliability sensitivities can be estimated more accurately by the derived equations based on the equivalent hyperplane.An example shows that the method is effective and feasible.
Reliability sensitivity;Failure probability;Nonlinearity;Multi-hyperplane combination method;Equivalence
1.Introduction
Reliability sensitivity analysis plays an important role in reliability design,reliability-based optimization design and reliability-based robust design.Reliability sensitivities are useful to quantify the distribution parameters such as mean and standard deviation,and represent that the distribution parameters infuence the reliability to some degree.The reliability sensitivities are often expressed as the sensitivity of the computed failure probability to changes in the distribution parameters.
Among the methods available for the parametric sensitivity analysis,the method based on FORM is a fundamental and widely used approach due to the high computational effciency and acceptable accuracy of FORM[1-3].Obviously,FORM is to replace a certain limit state hypersurface with a hyperplane and makes it easy to calculate the failure or safety probability.Because of this,FORM may overestimate or underestimate the reliability when the hypersurface is nonlinear near the design point.The higher the curvature of the limit state hypersurface at the design point is,the bigger the computational error of the reliability is.Just as FORM usually overestimates or underestimates the reliability,it may underestimate or overestimate the degree to which the distribution parameters infuence the reliability.Therefore,the parametric sensitivity analysis based on FORM may be unsatisfactory or unacceptable.
Compared with FORM,SORM(second-order reliability method)can compute the reliability more accurately.But because of the diffculty in computing the reliability,the parametric sensitivity analysis based on SORM was seldom discussed[4].MCSM(Monte Carlo simulation method)can be used for the sensitivity analysis[5-8].The simulatedresults of the sensitivity analysis by MCSM are quite accurate, but one main shortcoming of MCSM is that the computational amount is too large.
MHCM(multi-hyperplane combination method)is an alternative to improve the calculation accuracy of the reliability for a nonlinear limit state function[9-11].In MHCM, some hyperplanes are utilized to replace the limit state hypersurface.Feng[9]frst studied MHCM for obtaining much more accurate computational result of reliability.Mahadevan et al.[10]used the idea of MHCM for a little more complex reliability calculation with multiple extreme points,but the handling method in Ref.[10]is rough and the calculation accuracy of the reliability is not high enough.Shin et al.[11] introduced a progressive importance sampling method based on multi-hyperplane combination and the importance sampling for the reliability analysis of the nonlinear performance function with multiple design points.Lu et al.[12]studied how to obtain some hyperplanes and how to compute reliability easily when MHCM was used.The computed results of MHCM are different when a different number of the hyperplanes and the different hyperplanes are selected.And the different way to calculate the reliability of the system consisting of the obtained hyperplanes may lead to the results with different calculation accuracies.Anyhow,compared to FORM, MHCM can improve the calculation accuracy of the reliability greatly.Compared to MCSM,MHCM requires less computational amount.
As MHCM can get more accurate computational result of the reliability,it can obtain more accurate results of the reliability sensitivity analysis compared to FORM.In this paper, some equations of computing the sensitivities for the calculated failure probability were derived according to MHCM, and an example was given to show that the method of the sensitivity analysis based on MHCM is effective and feasible in improving the calculation accuracy of the sensitivity analysis.
2.Basic models of MHCM
Assuming thatx1,x2,x3,…,xnare basic random variables which are independently subjected to standard normal distribution and x=[x1,x2,x3,…,xn]is a 1×norder matrix,a nonlinear limit state function can be expressed byZ=g(x), and the limit state hypersurface can be expressed byZ=g(x)=0.To obtain a number of hyperplanes to replace the limit state hypersurface,the same number of points on the hypersurface and near the design point is obtained by extrapolation method and one-dimensional iterative search method[12].Then,a number of hyperplanes can be built at the obtained points by the frst-order Tayler series expansion.
In Fig.1,the hyperplane(for two dimensions,namely,two random variables,the hypersurface is reduced to a line)at the design point x0is acquired by the frst-order Tayler series expansion of the nonlinear limit state function,which is called as a main hyperplane,denoted byZl0=0.The other hyperplanes at the above obtained points except x0are called as subhyperplanes,denoted byZli=0(i=1,2,…,k).

Fig.1.Reliability computated by MHCM.
As shown in Fig.1,the dotted lines express the course of equivalent calculation,and each dotted line is expressed as a main equivalent approximate line by an equivalent calculation. The last main equivalent approximate line is expressed by a thick solid line.
The safety domainDSiof each hyperplane(main hyperplane or sub-hyperplanes)can be denoted by

Because the limit state functionZliis linear,the safety probabilityPSiin which the values of x are located inDSican be given accurately by

where Φ(·)is the accumulative integral function of standard normal distribution;and βiis the reliability index of the linear limit state functionZli.
In Fig.1(a),when the original nonlinear failure domain is a local convex set,the original nonlinear safety domainDScan be expressed approximately by the set union of allDSias follows
四是查处违法违规违纪行为。在项目采购人自查自纠中,对 “零报告”和“隐瞒、迟报、谎报”的,列为重点核查对象,一经查实,将对采购人及当事人进行严肃追责。对于查处结果,发现存在一般性违规违纪问题的,督促项目采购主管部门和项目采购人整改到位;存在严重违法违规问题的,将按照法律法规和相关文件要求进行处理,并对当事人进行严肃追责。同时,曝光一批群众反映强烈、情节恶劣的违法违规违纪行为。对涉嫌违纪、职务违法、职务犯罪的,移送纪委监委处理;涉嫌其他犯罪的,依法移交公安等司法机关查处。

According to the basic model of system reliability,the system consisting of the above hyperplanes is a parallel one. The safety probabilityPSin which the values of x are located inDScan be given by
在英语教学活动中,很多教师都切身感受到,学生们对英语精读课缺乏积极学习的热情,有的学生甚至对英语精读课感到“厌烦”,有些学生感觉他们从精读课上没学到更多东西。这种现象,主要原因在于学生们没有掌握学习要领,缺乏精读学习的技巧,这就需要精读课程的教师,要深入研究技巧的培育,不仅仅授学生以鱼,更要授之以渔。

It is a little complicated to calculatePSdirectly using Eq. (4),because the operation of set union should be transformed into that of set intersection.Based on the duality of system reliability,when the original nonlinear failure domain is a convex set,the nonlinear failure domain can also be expressed by set intersection of failure domainDFiof each hyperplane,as shown in Fig.1(a).DFiis written as It is well known that not only the failure domain but also the safety domain of each hyperplane is a linear domain.The failure probabilityPFiin which the values of x are located in


DFican be obtained The original nonlinear failure domainDFcan be expressed approximately by the set intersection of allDFias follows The failure probabilityPFin which the values of x are located inDFcan be given by


Assuming thatDis the full probability space,we haveDF∪DS=D,DF∩DS=φ,andPF+PS=1.So,PForPScan be computed to obtain the reliability.From the above discussion,it is known that,when the original nonlinear failure domain is the convex set,it is much more easy to compute the failure probabilityPFof the original nonlinear limit state function,that is to say,to compute the joint probability of the failure domains of the obtained hyperplanes.
Accordingly,as shown in Fig.1(b),when the original nonlinear safety domain is a local convex set,it is easy to compute the safety probability of the original nonlinear safety domain by using the safety domain of each hyperplane.The safety domain is replaced approximately by the set intersection of the safety domains of the above obtained hyperplanes, namelyPScan be obtained as
再比如《黄鹤楼送别》描写李白站在江边目送孤帆远去,可不可以添写李白的内心独白?答案是画蛇添足。老师可以告诉学生这叫“无声胜有声”。有时候一个眼神、一个姿势可以表达无尽情谊,语言反倒显得苍白。


In fact,the computation of the safety probability is transformed into that of series system consisting of the above hyperplanes.
Therefore,computingPForPSdepends on whether the failure domain or the safety domain is a convex domain.It is much more easy to calculate the probability of a convex domain.
无论是PBL教学法、TBL教学法、虚拟现实教学法还是标准化病人教学法,都有着优势与不足。但是即使教学模式产生了巨大变化,它的根本目的也不会改变,就是让学生在最少的时间里最大程度的掌握医学知识和临床实践技能。……
杂志排行
Defence Technology的其它文章
- In fluence of Al2O3particles on the microstructure and mechanical properties of copper surface composites fabricated by friction stir processing
- Theoretical study of an energetic material di-1H-1,3,4-triazole derivatives
- Research on modeling of nonlinear vibration isolation system based on Bouc-Wen model
- Feasibility of surface-coated friction stir welding tools to join AISI 304 grade austenitic stainless steel
- Experiment and simulation of launching process of a small-diameter steel cartridge case
- Scale-up synthesis and characterization of 2,6-diamino-3,5-dinitropyrazine-1-oxide
