Ti-5Al-5Mo-5V-1Cr-1Fe合金的高温塑性变形行为
2012-09-29张晓泳唐仁波周科朝
李 超,张晓泳,,唐仁波,周科朝
(1. 中南大学 粉末冶金国家重点实验室,长沙 410083;2. 中南大学 冶金科学与工程学院,长沙 410083;3. 湖南金天钛业科技有限公司,常德 410007)
Ti-5Al-5Mo-5V-1Cr-1Fe合金的高温塑性变形行为
李 超1,张晓泳1,2,唐仁波3,周科朝1
(1. 中南大学 粉末冶金国家重点实验室,长沙 410083;2. 中南大学 冶金科学与工程学院,长沙 410083;3. 湖南金天钛业科技有限公司,常德 410007)
在Gleeble-1500 热模拟机上对Ti-5Al-5Mo-5V-1Cr-1Fe合金进行高温热压缩实验,研究该合金在变形温度为750~900 ℃、应变速率为0.001~1 s−1条件下的流变应力行为。利用光学显微镜分析合金在不同变形条件下的组织演化规律。结果表明:合金的流变应力随着应变速率的增大和变形温度的降低而增大;流变应力随着应变的增加而增大,出现峰值后逐渐趋于平稳;变形过程中的流变应力可用Arrhenius双曲正弦本构关系来描述,平均变形激活能为454.2 kJ/mol;各种变形条件均可细化原始晶粒尺寸。随着温度的升高和应变速率的降低,合金的主要软化机制由动态回复逐渐变为动态再结晶;在(α+β)相区变形(750~850 ℃)时,α相对β晶粒的动态再结晶的发生起到阻碍作用。
Ti-5Al-5Mo-5V-1Cr-1Fe合金;热变形;流变应力;显微组织
Abstract:The hot deformation behaviors of Ti-5Al-5Mo-5V-1Cr-1Fe alloy were studied by a Gleeble-1500 machine at 750−900 ℃ with the strain rate of 0.001−1 s−1. The microstructural evolution of the alloy was investigated by optical microscopy. The results indicate that the flow stress of the alloy increases with increasing strain rate and decreasing deformation temperature. The flow stress increases with increasing strain until the stress reaches the peak value, then the flow stress remains constant. The flow stress in deformation can be described by Arrhenius hyperbolic sine constitutive equation, and the average activation energy is 454.2 kJ/mol. The original grain size can be refined under all deformation conditions. The main softening mechanism is changed from dynamic recovery to dynamic recrystallization with increasing the deformation temperature and decreasing the strain rate. In the (α+β) region (750−850 ℃), α phase can inhibit the dynamic recrystallization of β grains particles during deformation.
Key words:Ti-5Al-5Mo-5V-1Cr-1Fe alloy; hot deformation; flow stress; microstructure
高强高韧近β钛合金具有比强度高、疲劳性能和断裂韧性等匹配性高等特点,且具有较宽的加工锻造窗口,适于加工大尺寸结构件,在制造大型运输机起落架等承力构件方面具有广泛的应用前景[1−4]。1990年代初期,以 Ti1023(Ti-10V-2Fe-3Al)等为代表的近β钛合金锻件开始在B-777等机型上得到广泛应用[5],其中包括前起落架和襟翼滑轨在内的超过200个部件使用该材料,实现了显著的减重效果[4−5]。……
